ITT Goulds Pumps 3405 Installation, Operation And Maintenance Instructions Download Page 17 | Manualshive

Page: 17 / 61

background image

Figure 5:

2.

Installations With Pump Above Source of Supply - Suction Lift:

a) Keep suction pipe free from air pockets. See

Figure 5: on page 15

• Piping should slope upwards from source of supply.
• No portion of piping should extend above

the pump suction nozzle.

b) All joints must be air tight.

c)

The suction pipe should always be submerged into the source of supply as shown in

2.5 Install suction piping

3405-3406-3416 Installation, Operation and Maintenance Instructions

15

«
...
15
16
17
18
19
...
»

Summary of Contents for Goulds Pumps 3405






























































Reviews:

No comments

Related manuals for Goulds Pumps 3405

Brand: GE Pages: 36

Standard Series

Brand: Facilities Resource Group Pages: 61

Aquarea WH-ADC0309J3E5B

Brand: Panasonic Pages: 40

Brand: Calpeda Pages: 43

Optyma Blue OP-LGHE068NTA07D

Brand: Danfoss Pages: 8

Brand: Ozito Pages: 6

Brand: RainScapes Pages: 2

Brand: Redring Pages: 4

Brand: Bard Pages: 41

Brand: Kärcher Pages: 50

Brand: Truma Pages: 36

Brand: Graco Pages: 10

Brand: EBARA Pages: 172

Brand: Gude Pages: 58

Brand: STAR Water Systems Pages: 2

SCM 4 PLUS 115/92

Brand: Flotec Pages: 22

Thermo Pro 90 HDD

Brand: Webasto Pages: 6

Brand: ICP Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands