ITT Goulds Pumps 3405 Installation, Operation And Maintenance Instructions Download Page 40 | Manualshive

Page: 40 / 61

background image

6.

An alternate method of removing the packing and lantern ring is as follows: Remove the upper half
casing. See

7.4 Dismantling of pump on page 45

1, 2, 4, 5. Remove the packing and lantern ring

from the stuffing box. This method permits the inspection of the shaft sleeve and the stuffing box
bushing. If the shaft sleeves are found to be deeply grooved in the packing area, they should be
replaced as it is only possible for the packing to do an efficient job when the sleeve surface is rela-
tively smooth.

7.2 Repacking stuffing boxes

38

3405-3406-3416 Installation, Operation and Maintenance Instructions

«
...
38
39
40
41
42
...
»

Summary of Contents for Goulds Pumps 3405






























































Reviews:

No comments

Related manuals for Goulds Pumps 3405

Brand: Bacharach Pages: 12

Brand: Watts Pages: 8

Brand: Walrus Pages: 12

Brand: Barnes Pages: 16

Brand: Bard Pages: 42

Brand: Zodiac Pages: 16

Brand: Kawamoto Pump Pages: 28

Brand: Oase Pages: 76

Brand: DROPSA Pages: 9

Brand: Ingersoll-Rand Pages: 12

Brand: Samoa Pages: 38

Sanitary Series

Brand: TapFlo Pages: 50

Brand: Macnaught Pages: 24

Brand: A.O. Smith Pages: 28

Brand: Calorex Pages: 44

Brand: Esco Pages: 7

Brand: Grundfos Pages: 8

JUNG PUMPEN HEBEFIX EXTRA

Brand: Pentair Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands