ITT GOULDS PUMPS 3296 EZMAG Installation, Operation And Maintenance Manual Download Page 49 | Manualshive

Page: 49 / 100

background image

Temperature

Oil requirement

Pumped-fluid temperatures exceed 177°C |
350°F

Use synthetic lubrication.

5.6.2 Acceptable oil for lubricating bearings

Acceptable lubricants

Table 3: Acceptable lubricants

Brand

Lubricant type

Chevron

GST Oil 68

Exxon

Teresstic EP 68

Mobil

DTE Heavy Medium

Phillips 66

Turbine Oil VG68

Shell

Turbo T 68

Royal Purple SYNFILM ISO VG 68 Synthetic Oil
Gulf

Harmony 68

5.6.3 Lubricate the bearings with oil

WARNING:

Risk of explosive hazard and premature failure from sparks and heat generation. Ensure bear-
ings are properly lubricated prior to startup.

Use a high-quality turbine oil with rust and oxidation inhibitors.

1.

Remove the fill plug.

2.

Fill the bearing frame with oil through the filler connection, which is located on top of the bearing
frame.
Fill the bearing frame with oil until the oil level reaches the middle of the sight glass (319). The cor-
rect volume of oil required for each size of bearing frame can be found in the ‘Oil Volume Require-
ments’ section in the ‘Bearing Maintenance’ / ‘Maintenance’ portion of the IOM.

113A

319

Oil lubricated

bearings

Correct

level

Figure 26: Oil filler connection

3.

Replace the fill plug.

5.6 Bearing lubrication

Model 3296 EZMAG Installation, Operation, and Maintenance Manual

47

«
...
47
48
49
50
51
...
»

Summary of Contents for GOULDS PUMPS 3296 EZMAG





































































































Reviews:

No comments

Related manuals for GOULDS PUMPS 3296 EZMAG

iSOLAR PDP Series

Brand: ICON Pages: 24

ZHHS-01-10K-R290-V5-M

Brand: JBG HT Pages: 32

Brand: Kamco Pages: 36

Brand: Barnstead|Thermolyne Pages: 56

Brand: Graco Pages: 56

Streamline 270MDV

Brand: Solahart Pages: 56

Brand: SAMES KREMLIN Pages: 51

Brand: Quantum Pages: 36

Brand: Faber Pages: 9

Brand: Honda Pages: 25

Brand: salmson Pages: 195

SINGLE PACKAGE DUAL FUEL HEAT PUMP

Brand: York Pages: 8

Brand: Walter Pages: 12

Brand: YAMADA Pages: 22

Brand: Perfect Aire Pages: 34

Brand: Fluke Pages: 2

Brand: Ferroli Pages: 42

Brand: BATHMATE Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands