CORNER BRACKETS
At the end of the season nets can be tied into a bundle and placed into a
pillow case (not to damage washing machine) and washed at 40 C0 with
normal washing powder. The ground frame can be washed with hot soapy
water. Any scuff marks on posts can be rubbed off with a light abrasive
scouring pad.
WARNING: Check the position of any underground services before using the
ground anchors and pegs. We take no responsibility for any damage or
injury caused in this manner.
NEVER use the goals without the ground anchor system. In severe weather
or windy conditions it is advisable to take your goal down as damage is not
covered by the guarantee in such circumstances. If you find the nets are
worn along the floor it may be rodents, by spreading pepper along the base
frame rodents will be deterred. It is advisable in any contact sport to take
out the relevant insurance's to cover against injury both from taking part,
equipment and other unforeseeable circumstances. Crossbars will not be
replaced within the guarantee period if broken by swinging or climbing or
any other misuse.
DO NOT try to glue any damaged fixings. Plastic materials in this product
vary and this may cause the plastic to break. Always replace any damaged
components.
SQUARE MESH Net is cut to shape. Simply throw over the frame and fit
each end onto top stanchion by securing on each corner of crossbar.
NOTE: If your net does not fit the first time, you may be fitting it to the
goal frame upside down i.e. that is to say the net from the crossbar to
the floor (a) is longer than the length of the net to the bottom of the
upright.(b)
a
b
a
b
We advise adult supervision during assembly and use. Observe and follow
warning labels attached to goal. Do not use any components, nets or parts
if they are damaged or broken. Spare parts and replacement nets are
readily available. If others are to install your goal you should show them
how to erect and dismantle the goal and hand them a copy of the fitting
instruction. If you lose your instructions copies can be attained from our
company website. To avoid damage when dismantling the goal follow
these guidelines: it is advisable in extreme windy conditions to dismantle
the goal and store away. Do not drop any heavy objects on ends of tubes.
When dismantling the goal ensure that all fittings are packed away and
that non are left on the playing surface. Warning goals must never be left
up or used unless they are properly fitted with ground anchors with net
attached and securely pegged down.
Do not use the goal in sub zero temperatures. warning labels should be
replaced when worn and we recommend replacing them every two years -
spare labels available. damaged components requested under guarantee
must be returned for inspection. Failure to follow the warnings, fitting
instructions contained in this document, may invalidate your guarantee.
The company , its agents and representatives do not accept any product
liability if used outside the EU. Use of the product in other countries outside
the EU including the USA is not covered and appropriate insurance should
be taken out by the user to cover for any eventuality. We reserve the rights
to amend the specifications of our soccer products in the interest of
continued development. Your product therefore may differ slightly to those
illustrated. Not suitable for children under 36 months until assembled due
to small parts.
TEL:
0114 24 34 200
SPARE PARTS
NET TIES
!
1
TEETH
3
2
NET CORD
4
6
7
8
Ensure the teeth of the
Net tie are facing you
(see step
1
).
Loop the Net Tie around
the Net Cord and slide
the end into the
horizontal slot and pull
tight onto Net Cord (see
step
1- 2
).
The vertical slot of the
Net Tie is used to
secure the net to the
post. Loop the Net Tie
around the post and
insert through
vertical slot and twist to
lock. (steps
3 - 5
).
Any excess Net Tie can
looped back into the
vertical slot. This will
also secure the net tie in
a fixed position (steps
6
- 8
). If Net Ties are to be
removed after use then
do not loop back into
vertical slot.
5
POST SECTION
PULL
TIGHT
WORLDWIDE © COPYRIGHT 2001 ITSA GOAL, ALL RIGHTS RESERVED A REGISTERED DESIGN
WE RESERVE THE RIGHTS TO AMEND THE SPECIFICATIONS OF OUR SOCCER PRODUCTS IN THE INTEREST OF CONTINUED DEVELOPMENT. YOUR PRODUCT THEREFORE MAY DIFFER LIGHTLY TO THOSE ILLUSTRATED. E&OE
Ensure locking pin
Is inserted Fully in
the posts
DO NOT THROW THE PINS AWAY
3
Push locking pin
Down centre of
Arrow Head
2
Insert Arrow Head
into Holes on
posts
1
Push and Lock the spig-
ots to two of the four
Corner Brackets.
Push and Lock the Blanking
Caps to the two remaining
Corner Brackets. (already
inserted)
Push and Lock the Large
Quick Release Buttons into
the ends of the Corner
Brackets.
Push and Lock the Small
Quick Release Buttons into
the ends of the Spigots.
NOTE : All plastic extrusions vary and therefore some tubes may be looser
or tighter to connector fittings. If you want to increase the diameter of the
fitting just wrap masking tape around the part that fits into the tube, twist
as you insert the fitting and it will grab to the tube tight ...you can make
tighter fits by adding more tape.
To register for your guarantee visit
www.itsagoal.net
scroll to the bottom of the page and click on the link ‘Guarantee’
and follow the instructions. Thank you.
REGISTER YOUR GUARANTEE
Guarantee
