ITech IT9120 Series Programming Manual Download

Page: 76 / 90

CALCulate Commands

Query Syntax

INTegral:STOP:TINTerval?

INTegral:CONDition?

This command is used to obtain the integral running state.

Command Syntax

INTegral:CONDition?

Returned value

Ready|Start|Stop|Time up|Error

Query Syntax

INTegral:CONDition?

[:CALCulate][:METer]:MAXHold[:STATe] <bool>

This command is used to set the hold mode of maximum value.

Command Syntax

CALCulate:METer:MAXHold <bool>

Parameters

0|1|OFF|ON

Query Syntax

CALCulate:METer:MAXHold?

[:CALCulate][:METer]:CLEar[:IMMediate]

This command is used to clear measuring value to zero.

Command Syntax

CALCulate:METer:CLEar:IMMediate

Parameters

None

Query Syntax

None

[:CALCulate]:HARMonic[:STATe] <bool>

This command is used to set the harmonic state.

Command Syntax

CALCulate:HARMonic <bool>

Summary of Contents for IT9120 Series



























































































Search results

Summary of Contents for IT9120 Series

Reviews:

Related manuals for IT9120 Series

Brands by name

Popular brands

ITech IT9120 Series, Programming Manual

Search results

Summary of Contents for IT9120 Series

Reviews:

Related manuals for IT9120 Series

Brands by name

Popular brands