ITech IT9120 Series Programming Manual Download

Page: 64 / 90

Oscilloscope Commands

Chapter11 Oscilloscope Commands

WAVE:TRIG:SOUR< VOLTage|CURRent|EXTernal >

This command can set or read the device taking which kind waveform as trigger
source.

Command Syntax

WAVE:TRIG:SOUR < VOLTage|CURRent|EXTernal >

Parameters

VOLTage|CURRent|EXTernal

Query Syntax

WAVE:TRIG:SOUR?

WAVE:TRIG:SLOP <POSitive|NEGative|ANY>

This command is used to set trigger slope when takes waveform as trigger
source.

Command Syntax

WAVE:TRIG:SLOP < POSitive|NEGative|ANY >

Parameters

POSitive|NEGative|ANY

Query Syntax

WAVE:TRIG:SLOP?

WAVE:TRIG:MODE <AUTO|NORMal>

This command is used to set the trigger mode when take waveform as trigger
source.

Command Syntax

WAVE:TRIG:MODE < AUTO|NORMal >

Parameters

AUTO|NORMal

Query Syntax

WAVE:TRIG:MODE?

WAVE:TRIG:DELay:TIME <n>

This time is used to set the trigger delay time when take a waveform as trigger
source.(Note:the delay time setting should be less than the time width of the
whole screen.

Summary of Contents for IT9120 Series



























































































Search results

Summary of Contents for IT9120 Series

Reviews:

Related manuals for IT9120 Series

Brands by name

Popular brands

ITech IT9120 Series, Programming Manual

Search results

Summary of Contents for IT9120 Series

Reviews:

Related manuals for IT9120 Series

Brands by name

Popular brands