background image

User Manual

6

SP5BT 

GETTING STARTED

1. Fully charge the battery of the headset and docking 
     base before initial use:

1)  Dock the headset into the docking base.

2)  Slide the CHARGE switch on the docking base to the right.

3)  Connect the charging cable to the charging port on the docking 

      base.

4)  Connect the other end of the charging cable to the AC adapter, car 

      adapter or the USB port of your PC. Charging is indicated by a red 

      LED on the docking base.

5)  Allow both the headset and docking base to charge completely; 

      this may take up to 6.5 hours, depending on the power source 

      you are using.  USB charging is slower than using a car or AC 

      charger.  Charging is complete when the charging LED turns off.

.  Pair the headset with a Bluetooth-enabled mobile 
      phone:

1)  Ensure the headset is powered off – the headset must be powered 

      off to enter pairing mode.

2)  Ensure the Bluetooth radio on your mobile phone is powered on.  

      Please refer to the phone user manual for details.

 

3)  Hold the multifunction key on the headset for 5 seconds.  A blue 

      LED flashes rapidly, then changes to flash alternately red and blue.

      The headset is ready to pair.

4)  Set the mobile phone to search for Bluetooth devices and follow 

      the instructions on the phone’s screen.  Please refer to the phone 

      user manual for details.  You will recognize the iSymphony SP5BT 

      headset by its Bluetooth name “iSymphony SP5.”

5)  Select the iSymphony SP5BT for pairing.  When prompted for a  

      passkey, enter “1234.”

6)  Select the newly paired SP5BT for connection.  Within a few seconds 

      connection is complete and a blue LED flashes slowly on the 
      headset.

Summary of Contents for SP5BT

















Reviews: