Isuzu Trooper II 1986 Manual Download Page 22

Page: 22 / 25

COOLING section.

TORQUE SPECIFICATIONS

TORQUE SPECIFICATIONS TABLE

Application Ft. Lbs. (N.m)

Camshaft Pulley Bolts ............................ 58 (79)

Connecting Rod Caps .............................. 33 (45)

Connecting Rod Caps 2.3L ........................ 43 (58)

Cylinder Head Bolts 1.9L

Step 1 ......................................... 61 (83)

Step 2 ......................................... 72 (98)

Cylinder Head Bolts 2.0L & 2.3L

Step 1 ......................................... 58 (79)

Step 2 ........................................ 79 (107)

Exhaust Manifold ................................. 16 (22)

Flex Plate (Auto. Trans.) ....................... 76 (103)

Flywheel (Man. Trans.)

2.0L & 2.3L ................................ ( 1) 45 (33)

1.9L .......................................... 76 (103)

Front Cover ...................................... 18 (24)

Front Pulley Bolts ............................... 18 (24)

Front Pulley Boss Bolt .......................... 87 (118)

Intake Manifold .................................. 16 (22)

Main Bearing Caps ................................ 72 (98)

Oil Pump Sprocket ................................ 58 (79)

Oxygen Sensor

2.0L & 2.3L .................................... 33 (45)

1.9L ........................................... 18 (24)

Rocker Arm Shaft Brackets .................... ( 2) 16 (22)

Rear Oil Seal Retainer ........................... 18 (24)

Water Pump

2.0L &2.3L ..................................... 14 (19)

1.9L ........................................... 18 (24)

(1) - With Loctite applied to first thread.

(2) - Tighten No. 9 and 10 bolts to 72 INCH lbs. (8 N.m)

on 2.0L & 2.3L models.

ENGINE SPECIFICATIONS

GENERAL ENGINE SPECIFICATIONS

GENERAL SPECIFICATIONS TABLE

Application Specifications

Impulse

Displacement

Cu. In. .......................................... 121.7

Liters ............................................. 2.0

Fuel System ................................... Fuel Inj.

HP @ RPM ..................................... 140 @ 5400

Torque Ft. @ RPM ............................. 166 @ 3000

Compr. Ratio ........................................ 7.2

Bore

In. (mm) ..................................... 3.46 (88)

Stroke

Summary of Contents for Trooper II 1986


























Search results

Summary of Contents for Trooper II 1986

Reviews:

Related manuals for Trooper II 1986

Brands by name

Popular brands

Isuzu Trooper II 1986, Manual

Search results

Summary of Contents for Trooper II 1986

Reviews:

Related manuals for Trooper II 1986

Brands by name

Popular brands