15-
5.1. Master/Slave Built-In Preprogrammed Function
Once you control the unit by Built-In program, be sure the unit is setting on
mode
via menu.
By linking the units in master/slave connection, the first unit will control the other units to
give an automatic, sound activated, synchronized light show. This function is good when you
want an instant show. You have to select show (show 1, 2, 3, 4) modes for the first unit
(master). Its DMX input jack will have nothing plugged into it, and Its master LED will be
constantly on and sound LED will flash to the music. The other units will have to set in slave
mode
and select
(normal) or
(2 light show) mode, Their DMX
cables plugged into the DMX input jacks (daisy chain) and the slave LED lights will
constantly on.
2-light show
In
(slave mode),
means the unit works normally and
means
2-light show. In order to create a great light show, you can set
on the second unit
to get contrast movement to each other, even if you have two units only.
5.2. Easy Controller
The easy remote control is used only in master/slave mode. By
connecting to the 1/4” microphone jack of the first unit, you will find
that the remote control on the first unit will control all the other units for
Stand by, Function and Mode.
Stand by Blackout the unit
Function
Strobe
1. Color sync. strobe
2. Sync. strobe
3. Two-light strobe
X/Y moving show pattern
selection
( Show 1 ~ Show 4 )
Please refer to 4.2. Main
Functions- Show mode
Gobo/Color selection
1.Hold on for gobo
selection
2.Press for color change
X/Y moving setting
1.Macro(sound active)
2.Fade (sound invalid)
Mode
Sound 1
(LED off )
Sound 2
(LED slow blinking)
Slow/Sound 3
(LED on)
Position/ Latch
(LED fast blinking)
5.3. DMX Controller
If you use a universal DMX controller to control the units, you have to set DMX address from
1 to 512 channel so that the units can receive DMX signal.
Press the
MENU
button up to when the
is shown on the display. Pressing
ENTER
button and the display will blink. Use
DOWN
and
UP
button to change the DMX512 address.
12-
Display normal mode for the fixture putting on the floor.
Display inversion mode for the fixture fixing under ceiling.
Focus Adjust
Press the
MENU
button up to when the
is blinking on the display. Pressing
ENTER
button, the unit will focus on tilt 90°, and then the unit will focus on tilt 0°, pan 0°, pan 90°,
pan 180°, pan 270° in every pressing
ENTER
button. To go back to the functions press the
MENU
button again.
Self-Test
Press the
MENU
button up to when the
is blinking on the display. Pressing
ENTER
button and the unit will run self-test by built-in program. To go back to the functions press the
MENU
button again.
Ambient temperature of lamp
Press the
MENU
button up to when the
is blinking on the display. Pressing
ENTER
button and the ambient temperature of lamp will show on the display. To go back to
the functions press the
MENU
button again.
Fixture Hours
Press the
MENU
button up to when the
is blinking on the display. Pressing
ENTER
button and the display will show the number of working hours of the unit. To go back to the
functions press the
MENU
button again.
Lamp ON/OFF
Press the
MENU
button up to when the
is blinking on the display. Pressing
ENTER
button and the display will blink. Use
DOWN
and
UP
button to select the
(Lamp on)
or
(Lamp off) mode. Once the mode has been selected, press the
ENTER
button
to setup. Idling 8 seconds automatically exit menu mode. Back to the functions without any
change press
MENU
button.
Reset
Press the
MENU
button up to when the
is blinking on the display. Pressing
ENTER
button and all channels of the unit will return to their standard position. It will cost about 20
Summary of Contents for IM-250SW
Page 2: ...1...