HT-309 AC110-120V 60Hz 600W
HT-309 AC110-120V 60Hz 600W
Inflation inlet
Deflation outlet
Plug
Air nozzle
Power switch button
Hose
Hose coupler
1
2
3
4
5
6
7
3
5
6
7
4
2
1
1
.
Product Introduction
HT-309 is an AC high flow electric air pump that may inflate inflatable
boats, water platforms, banana
boats, towable tubes, water trampolines, and water bouncers. Dispite its s
imple appearance design,
the product that follows very strict industry standards is easy to carry and bears features for both
inflation and deflation.
Whenever an inflatable product is to be put away, this pump may be used to the air inside for easy
folding and storage.
2
.
List of Accessories
Please make sure that the following accessories are in the box before using it, if any missing,
please contact with the local service agents.
Air pump
Hose/
Air nozzle
Instruction Book
*
*
*
*
*
*
*
*
*
*
*
(Figure 1)
(Figure 2)
5
.
Deflation operation
Remove the hose from the inflation inlet
.
Connect the end with flexible conduit adaptor of the hose
with the air pump deflation outlet
,
and twist clockwise to tighten it, as Figure 3
. T
he other end shall still
be to the airbag.
After completing the above steps, push the power switch to “ I ”to start the deflation.
After completing the deflation process, push the power switch to “ 0 ” to stop the deflation.
*
*
*
*
*
*
*
*
*
*
(Figure 3)
3
.
Safety Instructions
Never leave pump unattended while the pump is in use.
Do not use/store the pump in wet condition.
Never allow sands, small rocks,etc, to be sucked into inflation port when the pump is working.
Never look inside or point the inflation port toward your eyes when the pump is working.
Never attempt to put hand or fingers into the inflation port at any time.
4. In
flationperation
Connect one end of the hose coupler (7) with the pump inflation port (1) and tighten clockwise (Fig. 1).
Install the other end of the hose into the supporting air tap of the air bag (step 1 in Figure 2), and twist
clockwise to tighten it, and then insert the inflation valve of the air bag and twist clockwise to fix it (step
2 in Figure 2).
After completing the above steps, push the power switch to “ I ” to start the inflation.
After completing the inflation process, push the power switch to “ 0 ” to stop the inflation.
After completing the inflation, pull the plug of the inflating pump out of the socket.
After unplugging, please store the conduit coupler.
6
.
Precautions
Power supply must be AC 110-120V.
This is a high-volume pump. Please use this pump continuously not more than 15 minutes, otherwise,
it
can overheat and damage the pump.
After the pump has been working
continuously for more
th
an 15 minutes at a time,
let it
fully cool it down for 5
minutes.
Then continue to use.
Keep the pump out of the reach of children.
Do not obstruct the inflation port and keep them ventilated all the time.
Use in a dry space
i
ndoor
s or covered. Do
not expose it in rain
or water
, so as to reduce the risk of
electric shock.
This appliance has a polarized plug (one blade is wider than the other).This plug will fit in a polarized
outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact
a qualified electrician to install the proper outlet.
If the power cord is damaged, the power cord must be replaced to avoid danger.
This product shall not be exposed the rain or immersed in water.
In order to prevent risk, the inflation inlet shall not be forward to face or body. Please don't not leave while
inflating.
*
*
