background image

Graham-Patten is a division of  

 

Printing History 

SoundPals

   DMIX-41 Four Channel Digital Mixer  

Rev. N/C 
March 2007 
Printed in U.S.A.  
Part Number  

08-2047-00

 

The information contained in this guide is subject to change without notice or obligation. 

 

Copyrights and Trademarks  

© 2005 GRAHAM-PATTEN SYSTEMS, INC. 
Contents of this publication may not be reproduced in any form without the written permission of Graham-Patten.  
Reproduction or reverse engineering of copyrighted software is prohibited. 

 

FCC Compliance 

This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 
of the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference when the 
equipment is operated in a commercial environment.  This equipment generates, uses, and can radiate radio 
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful 
interference to radio communications.  Operation of this equipment in a residential area is likely to cause harmful 
interference in which case the user will be required to correct the interference at your own expense. 

 

Warranty Statement 

Graham-Patten warrants that the equipment it manufactures is free from defects in workmanship and materials and 
meets applicable published specifications.  Equipment that has been operated within published ratings and has not 
been subjected to abuse or modification, and which fails because of such defects, will be replaced or repaired at the 
Company’s discretion if it is returned, freight prepaid, to Graham-Patten within seven years of receipt.  
This warranty supersedes all other Warranties, express or implied.  Graham-Patten is not liable for any 
consequential damages.   

 

Company Address 
 

 

 
GRAHAM-PATTEN SYSTEMS, INC. 
119 East McKnight Way, Unit A  
Grass Valley, California  95949

 

Telephone:  (888) 622-4747, (530) 477-2984 
Fax:  (530) 477-2986 
e-mail:  [email protected] 
World Wide Web:  

www.gpsys.com

 

 

 

Summary of Contents for Graham-Patten SoundPals DMIX-41

























Reviews: