5 x 25 mm
3.9 x 30 mm
Ø 5 mm
Ø 26 mm
Ø 5 mm
8. INSTALLATION ON A WALL
83
26
5. ACTUATOR CONFIGURATION:
LOCKBUS SELECTION
1
6.1
STAND-ALONE GATE:
EXCHANGE OF CODED KEYS WITH ACTUATOR
(EXCHANGE KEYS)
Power supply
8
÷24VDC 25W
COM
NO/NC
GND
IN AN
I/O 2
I/O 1
VCC
GND
L2
L1
P1
P2
LRL
J P3
LPW
J P2
LCH
J P 1
LVO
V2 Output
V1 Output
OPEN
V PWR +
GND
EARTH
For more information regarding the exchange of keys, see the
Tutorial
Video
available at
app.iseo.com.
Switch on the Stylos Control
Unit keeping pressed the
button and wait for the acustic
and light signal, then release it
immediately.
1
2
Switch on the actua-
tor keeping pressed
one button for 3 sec.
Stylos Master
address 0
Actuator
address 1
6.
STAND-ALONE GATE:
EXCHANGE OF CODED KEYS WITH ACTUATOR
(JUMPER SETTING)
Power supply
8
÷24VDC 25W
COM
NO/NC
GND
IN AN
I/O 2
I/O 1
VCC
GND
L2
L1
P1
P2
LRL
J P3
LPW
J P2
LCH
J P 1
LVO
V2 Output
V1 Output
OPEN
V PWR +
GND
EARTH
Stylos Master
address 0
Switch on the Actuator and check if red led
flashes:
1 time
(Lockbus 1) =
Reader/Validator.
2 times
(Lockbus 2) =
Stand-Alone gate
.
Change the Lockbus type accordingly to your
configuration, following the next point.
2
Switch on the Actuator keeping pressed both
buttons simultaneously for 1 sec.
Switch on it again to check if now red led
flashes 1 or 2 times.
If not repeat the procedure.
Set jumpers on Actuator and Stylos Control Unit as per pictures below. Note this configuration is
correct only in case of 1 Stylos (Master) and 1 Actuator (Slave).
For more information about
jumper setting with different
configuration, refer to the
Stylos User Manual
available
at
app.iseo.com
.
7. INSTALLATION ON A METAL PROFILE
Ø 3.2 mm
(max)
Ø 3.2 mm
(max)
Ø 26 mm
3.9 x 19 mm
83
26
Power supply
8
÷24VDC 25W
COM
NO/NC
GND
IN AN
I/O 2
I/O 1
VCC
GND
L2
L1
P1
P2
LRL
J P3
LPW
J P2
LCH
J P 1
LVO
V2 Output
V1 Output
OPEN
V PWR +
GND
EARTH
9. INSTALLATION WITHOUT THE SPACER
1
2
9.1 INSTALLATION WITH THE SPACER
1
2
DRILLING TEMPLATE
TOP
B
O
TT
OM
Red led flashing
Actuator
address 1
Check the connections
on section 5 or 6
before powering the
device.
Take care to not
damage the cables
while installing the
device.
Check the connections
on section 5 or 6
before powering the
device.
Take care to not
damage the cables
while installing the
device.
JP
6
JP
4
JP
2
JP
0
J2.
1
J2.
2
J2.
3
J2.
4
JPS
S1
Control Unit
Circuit View
JP
6
JP
4
JP
2
JP
0
J2.
1
J2.
2
J2.
3
J2.
4
JPS
S1
Control Unit
Circuit View
