isel automation GFV 102/62 Operating And Maintenance Instruction Manual Download Page 8

Page: 8 / 23

isel

flat bed installation GFV

> 500 mm

> 150 mm

GFV

Setting up and connection

5.1

Spacial requirements

The spacial requirements of the machine are limited to the external dimensions of the

machine and the Penguin and sufficient free space is available in front of or at the side of

the machine in order to operate and install it. Normally, the cover of the enclosure turns

upwards. Thus, you must keep approx. 50 to 60 cm of free space in addition.

Dimensions and spacial requirements

Model

GFV 44/33

760

1010

1750

2300

GFV 44/73

1160

1010

1750

2300

GFV 68/52

1410

1260

1880

2480

GFV 102/62

1810

1410

1880

2480

GFV 142/102

2210

1810

1880

2480

GFV 142/162

2210

2410

1880

2480

GFV 142/232

2210

3110

1880

2480

Penguin without feet 550

675

1380

Dimensions in [mm]

Consider the total overall height (X) with the hood opened.

In case of the special sizes with increased portal, the enclosure increases by approx. 300

mm (H + 300 and X. + 300) by default.

Penguin

(Control

cabinet)

Summary of Contents for GFV 102/62
























Search results

Summary of Contents for GFV 102/62

Reviews:

Related manuals for GFV 102/62

Brands by name

Popular brands

isel automation GFV 102/62, Operating And Maintenance Instruction Manual

Search results

Summary of Contents for GFV 102/62

Reviews:

Related manuals for GFV 102/62

Brands by name

Popular brands