background image

Safety

This section contains important security information for the installation and operation of the device. Failure to follow safety 
instructions and warnings can result in serious injury or death and property damage.
Safety and operating instructions must be read carefully before starting any operation.
We decline all responsibility for damages and injuries caused which may arise from improper use of our equipment.

Depiction of the safety instructions

DANGER!

DANGER!

“Danger!” indicates a severe injury hazard. The non-observance of safety instructions marked as “Danger!” will 
lead to possible injury or death.

WARNING!

WARNING!

“Warning!” indicates an injury hazard. The non-observance of safety instructions marked as “Warning!” could 
lead to possible injury or death.

CAUTION!

CAUTION!

Advices marked as “Caution!” describe actions to avoid possible damages to property.

INFORMATION

INFORMATION

Advices marked as “Information” give important information.

Read the manual.

Attention high voltage!

Important information.

ECH 124 / 128 / 12A / 14A - MMC Crate | Last modified on: 24.01.2020 | www.iseg-hv.com

3/20

Summary of Contents for ECH 124





















Reviews: