IRT DDA-3010 Instruction Manual Download Page 1 | Manualshive

Page: 1 / 11

background image

3010-dda.ib.rev1.doc

Page 1 of 10

05/07/2006

IRT Eurocard Type

DDA-3010

140/155 Mb/s G.703 6 O/P

Reclocking Distribution Amplifier

Designed and manufactured in Australia

IRT can be found on the Internet at:

http://www.irtelectronics.com

I R T Electronics Pty Ltd A.B.N. 35 000 832 575

26 Hotham Parade, ARTARMON N.S.W. 2064 AUSTRALIA
National: Phone:

(02)

9439 3744

Fax: (02) 9439 7439

International:

+61 2 9439 3744

+61 2 9439 7439

Email: [email protected]
Web: www.irtelectronics.com

1
2
3
...
»

Summary of Contents for DDA-3010












Reviews:

No comments

Related manuals for DDA-3010

Brand: D.A.S. Pages: 15

Brand: Parasound Pages: 16

Stereo 25 MK II

Brand: icon Audio Pages: 8

Brand: Pass Pages: 6

Brand: Vanguard Dynamics Pages: 3

Brand: Tiger Electronics Pages: 8

Brand: Traynor Pages: 14

Brand: Traynor Pages: 16

NAC 112 - ISSUE 2

Brand: NAIM Pages: 30

Brand: RE Audio Pages: 12

Brand: R.V.R. Elettronica Pages: 79

Brand: Elite Acoustics Engineering Pages: 13

Brand: Hogtunes Pages: 12

Brand: Boston Pages: 12

Brand: Advance Paris Pages: 28

Valvestate VS100

Brand: Marshall Amplification Pages: 12

Phono Stage Preamplifie

Brand: Quicksilver Pages: 2

PT-100 SIGNATURE EDITION

Brand: Suhr Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands