Operation and Settting
2.4 Comfort Mode
The “Comfort” temperature corresponds to the temperature desired by the user and it is the temperature used for “Chrono”, “Pilot-wire” and
“Comfort” modes.
This operating mode is intended for normal use of the appliance.
Press the
[Mode]
key until the “Comfort” icon appears on the display;
Set the desired temperature with the
[+/-]
keys and wait for the temperature to stop blinking on the display.
The “Comfort” temperature can be set in the whole interval ("Night" mode tempe 0.5°C) to 32°C.
2.5 Night Mode
In “Night” mode the settable temperature is lower than the “Comfort” temperature. It is recommended to use this mode during the night or when
the room is not used for 2 hours or more.
The “Night” temperature is also used for “Chrono” mode.
Press the
[Mode]
key until the “Night” icon appears on the display;
To modify the “Night” temperature, use the
[+/-]
keys and wait for the temperature to stop blinking on the display.
NOTE: The “Night” temperature must always be lower than or the same as the “Comfort” temperature; for this reason the “Night”
temperature can be set between 7°C and the “Comfort” temperature minus 0.5°C.
2.6 Antifreeze Mode
In “Antifreeze” mode the temperature is fixed at 7°C. The appliance activates the heating element automatically when the room temperature falls
below 7°C.
It is recommended to use this mode when the room is not used for several days.
Press the
[Mode]
key until the “Antifreeze” icon appears on the display.
2.7 2h Timer Mode
“2h Timer” mode can be used to heat the room rapidly or to dry towels faster.
Press the
[Mode]
key until the “2h Timer” icon appears on the display.
The heating element is activated for 2 hours, irrespective of the set temperature (in any case, the maximum temperature that can be reached in
the room will be 32°C). At the end of the 2 hours, the thermostat returns to the mode set previously. If necessary, the user can deactivate the
function at any time by pressing the
[Mode]
key.
NOTE: Do not activate the 2h Timer mode directly from the Stand-by status
3 FUNCTIONS
3.1 Keyboard lock
It is possible to lock the keys of the device to avoid accidental modifications of the settings.
Hold down the
[+]
and
[-]
keys for 3 seconds to lock all the keys except the
[On/Stand-by]
key.
The key-lock icon will appear on the display.
To unlock the keys, hold down the
[+]
and
[-]
keys again for 3 seconds. The key-lock icon will disappear from the display.
3.2 “Detect open window” function
The “Detect open window” function allows an open window to be detected by perceiving a sudden decrease of the temperature in the room.
In this case, the device deactivates the heating element for a maximum of 30 minutes or until an increase in the ambient temperature indicates
that the window has been closed.
When this function is enabled, the
icon is lit.
When the device detects that the window might be open, the “Open window” icon starts to blink.
When the function is deactivated, the “Open window” icon is not shown on the display.
3.3 Adaptive Starting Control (ASC)
If activated, this function switches on the radiator earlier than the “Chrono” program (maximum 2 hours earlier) to ensure that the room has
reached the desired temperature at the set time.
Note: the function needs at least a couple of days to reach maximum efficiency.
4 SETTINGS
Setting of the device.
From “Stand-by” mode, hold down
the
[Mode]
key for at least 3 seconds.
The message "SEt" will be shown at the bottom of the display:
To select what you want to change:
Press the
[+]
key to choose between tEd (date and time), Pro9 (weekly program P3) and Funct (functions).
4.1 tEd (date and time):
Press the
[Mode]
key to enter editing mode.
The flashing number indicates the day of the week currently selected: press the
[+]/[-]
keys to set the desired day.
Press the
[Mode]
key again to confirm the selected day.
After that, the procedure for entering the time begins and the current time flashes on the display. “Hours”: use the
[+]
and
[-]
keys to set the
correct hour and confirm the selected value by pressing the
[Mode]
key.
“Minutes”: same procedure as for the hours. Confirm the selected value by pressing the
[Mode]
key.
At the end of the procedure, a double beep confirms the data acquired and the thermostat returns to “Stand-by” mode.
If you have any questions please contact us: 01342 302250, www.theradiatorcompany.co.uk
A brand of , Italy’s leading manufacturer of design led radiators
Operation and Settting
2.4 Comfort Mode
The “Comfort” temperature corresponds to the temperature desired by the user and it is the temperature used for “Chrono”, “Pilot-wire” and
“Comfort” modes.
This operating mode is intended for normal use of the appliance.
Press the
[Mode]
key until the “Comfort” icon appears on the display;
Set the desired temperature with the
[+/-]
keys and wait for the temperature to stop blinking on the display.
The “Comfort” temperature can be set in the whole interval ("Night" mode tempe 0.5°C) to 32°C.
2.5 Night Mode
In “Night” mode the settable temperature is lower than the “Comfort” temperature. It is recommended to use this mode during the night or when
the room is not used for 2 hours or more.
The “Night” temperature is also used for “Chrono” mode.
Press the
[Mode]
key until the “Night” icon appears on the display;
To modify the “Night” temperature, use the
[+/-]
keys and wait for the temperature to stop blinking on the display.
NOTE: The “Night” temperature must always be lower than or the same as the “Comfort” temperature; for this reason the “Night”
temperature can be set between 7°C and the “Comfort” temperature minus 0.5°C.
2.6 Antifreeze Mode
In “Antifreeze” mode the temperature is fixed at 7°C. The appliance activates the heating element automatically when the room temperature falls
below 7°C.
It is recommended to use this mode when the room is not used for several days.
Press the
[Mode]
key until the “Antifreeze” icon appears on the display.
2.7 2h Timer Mode
“2h Timer” mode can be used to heat the room rapidly or to dry towels faster.
Press the
[Mode]
key until the “2h Timer” icon appears on the display.
The heating element is activated for 2 hours, irrespective of the set temperature (in any case, the maximum temperature that can be reached in
the room will be 32°C). At the end of the 2 hours, the thermostat returns to the mode set previously. If necessary, the user can deactivate the
function at any time by pressing the
[Mode]
key.
NOTE: Do not activate the 2h Timer mode directly from the Stand-by status
3 FUNCTIONS
3.1 Keyboard lock
It is possible to lock the keys of the device to avoid accidental modifications of the settings.
Hold down the
[+]
and
[-]
keys for 3 seconds to lock all the keys except the
[On/Stand-by]
key.
The key-lock icon will appear on the display.
To unlock the keys, hold down the
[+]
and
[-]
keys again for 3 seconds. The key-lock icon will disappear from the display.
3.2 “Detect open window” function
The “Detect open window” function allows an open window to be detected by perceiving a sudden decrease of the temperature in the room.
In this case, the device deactivates the heating element for a maximum of 30 minutes or until an increase in the ambient temperature indicates
that the window has been closed.
When this function is enabled, the
icon is lit.
When the device detects that the window might be open, the “Open window” icon starts to blink.
When the function is deactivated, the “Open window” icon is not shown on the display.
3.3 Adaptive Starting Control (ASC)
If activated, this function switches on the radiator earlier than the “Chrono” program (maximum 2 hours earlier) to ensure that the room has
reached the desired temperature at the set time.
Note: the function needs at least a couple of days to reach maximum efficiency.
4 SETTINGS
Setting of the device.
From “Stand-by” mode, hold down
the
[Mode]
key for at least 3 seconds.
The message "SEt" will be shown at the bottom of the display:
To select what you want to change:
Press the
[+]
key to choose between tEd (date and time), Pro9 (weekly program P3) and Funct (functions).
4.1 tEd (date and time):
Press the
[Mode]
key to enter editing mode.
The flashing number indicates the day of the week currently selected: press the
[+]/[-]
keys to set the desired day.
Press the
[Mode]
key again to confirm the selected day.
After that, the procedure for entering the time begins and the current time flashes on the display. “Hours”: use the
[+]
and
[-]
keys to set the
correct hour and confirm the selected value by pressing the
[Mode]
key.
“Minutes”: same procedure as for the hours. Confirm the selected value by pressing the
[Mode]
key.
At the end of the procedure, a double beep confirms the data acquired and the thermostat returns to “Stand-by” mode.
4.2 Pro9 (weekly program P3):
Press the [Mode] key to enter P3 editing mode:
Programming begins at 00:00 on the first day of the week.
The upper side display shows the setting time 00 in the example, meaning from 00:00 to 01:00.
Press the [+] key if you want the “Comfort” temperature for this time or press the [-] key if you want the "Night" temperature, then automatically
show 01 which means from 01:00 to 02:00, choose the temperature as before. The empty bar means "Night" temperature, the full bar means
“Comfort” temperature.
After having set all 24 hours, press the [Mode] key to change to day no. 2 of the week and proceed with the same procedure as the previous
day to set all the other days of the week (7).
At the end of the procedure, a double beep confirms the data acquired and the thermostat returns to “Stand-by” mode.
4.3 Funct (functions):
To activate or deactivate “Detect open window” and ASC (Adaptive Starting Control).
Press the [Mode] button to enter editing, the detect open window icon will flash: press the [+] key if you want to activate (On) or press the [-]
key if you want to deactivate (Off);
Press the [Mode] button to enter editing, now the ASC icon will flash: press the [+] key if you want to activate (On) or press the [-] key if you
want to deactivate (Off);
Press the [Mode] button to confirm; at the end of the procedure, a double beep confirms the data acquired and the thermostat returns to “Stand-
by” mode.
Note 1: the device might not succeed in detecting an open window if, for example, the thermostat is in an isolated area of the room, far from draughts,
close to an external source of heat or if the temperature variation in the room is too slow.
Note 2: when the symbol is lit, the heating element is active.
Note 3: the icon indicates that the signal from the remote control is received.
Note 4: in the event of loss of power, the “Chrono” mode settings (current day of the week, current time, daily program for the week) remain in the
memory for at least 5 minutes.
Note 5:
Attention: in the case "Timer 2h" mode is activated directly starting from stand-by status ("S t b" word on display) and, finished the two hours,
electronics is blocked, execute the following procedure:
1. keep [Mode] button pressed for at least 1 second;
2. release [Mode] button and immediately press the [ON / Stand-by] button.
Point 2 must be done very quickly so we recommend making more than one attempt.
REMOTE CONTROL (OPTIONAL)
The electronic thermostat is equipped with an IR receiver and can therefore be controlled at a distance using an optional remote control.
All the modes and the functions described above are available on the remote control.
INFORMATION FOR USERS
in accordance with article 14 of the Directive 2012/19/EU of 07/07/2012 on waste electrical and electronic equipment.
•
The symbol shown above, present also on the equipment, indicates that it has been placed on the market and that, when the user decides to get
rid of it, it must be disposed of in separate waste collection (including all the components, sub-assemblies and consumer materials which are an
integral part of the product).
•
For information on the systems for collecting these appliances, please contact the company or another subject enrolled in the various National
Registers for other countries in the European Union. Waste produced in the home (or of similar origin) may be consigned to systems for the separate
collection of urban waste.
•
When buying a new appliance of an equivalent type, it is possible to hand over the old equipment to the seller. The seller will then contact the
subject in charge of the collection of the equipment.
•
The appropriate separate collection of the scrapped equipment and the subsequent operations of processing, recovery and environment-
compatible disposal, allows the avoidance of potential negative effects on the environment and on human health, while favouring the recycling and
recovery of the component materials.
The unauthorised disposal of the product by the user entails the application of the sanctions contemplated under the national approval of Directives
2011/65/EU, 2008/98/EC and 2015/1127/EU.
4.2 Pro9 (weekly program P3):
Press the [Mode] key to enter P3 editing mode:
Programming begins at 00:00 on the first day of the week.
The upper side display shows the setting time 00 in the example, meaning from 00:00 to 01:00.
Press the [+] key if you want the “Comfort” temperature for this time or press the [-] key if you want the "Night" temperature, then automatically
show 01 which means from 01:00 to 02:00, choose the temperature as before. The empty bar means "Night" temperature, the full bar means
“Comfort” temperature.
After having set all 24 hours, press the [Mode] key to change to day no. 2 of the week and proceed with the same procedure as the previous
day to set all the other days of the week (7).
At the end of the procedure, a double beep confirms the data acquired and the thermostat returns to “Stand-by” mode.
4.3 Funct (functions):
To activate or deactivate “Detect open window” and ASC (Adaptive Starting Control).
Press the [Mode] button to enter editing, the detect open window icon will flash: press the [+] key if you want to activate (On) or press the [-]
key if you want to deactivate (Off);
Press the [Mode] button to enter editing, now the ASC icon will flash: press the [+] key if you want to activate (On) or press the [-] key if you
want to deactivate (Off);
Press the [Mode] button to confirm; at the end of the procedure, a double beep confirms the data acquired and the thermostat returns to “Stand-
by” mode.
Note 1: the device might not succeed in detecting an open window if, for example, the thermostat is in an isolated area of the room, far from draughts,
close to an external source of heat or if the temperature variation in the room is too slow.
Note 2: when the symbol is lit, the heating element is active.
Note 3: the icon indicates that the signal from the remote control is received.
Note 4: in the event of loss of power, the “Chrono” mode settings (current day of the week, current time, daily program for the week) remain in the
memory for at least 5 minutes.
Note 5:
Attention: in the case "Timer 2h" mode is activated directly starting from stand-by status ("S t b" word on display) and, finished the two hours,
electronics is blocked, execute the following procedure:
1. keep [Mode] button pressed for at least 1 second;
2. release [Mode] button and immediately press the [ON / Stand-by] button.
Point 2 must be done very quickly so we recommend making more than one attempt.
REMOTE CONTROL (OPTIONAL)
The electronic thermostat is equipped with an IR receiver and can therefore be controlled at a distance using an optional remote control.
All the modes and the functions described above are available on the remote control.
INFORMATION FOR USERS
in accordance with article 14 of the Directive 2012/19/EU of 07/07/2012 on waste electrical and electronic equipment.
•
The symbol shown above, present also on the equipment, indicates that it has been placed on the market and that, when the user decides to get
rid of it, it must be disposed of in separate waste collection (including all the components, sub-assemblies and consumer materials which are an
integral part of the product).
•
For information on the systems for collecting these appliances, please contact the company or another subject enrolled in the various National
Registers for other countries in the European Union. Waste produced in the home (or of similar origin) may be consigned to systems for the separate
collection of urban waste.
•
When buying a new appliance of an equivalent type, it is possible to hand over the old equipment to the seller. The seller will then contact the
subject in charge of the collection of the equipment.
•
The appropriate separate collection of the scrapped equipment and the subsequent operations of processing, recovery and environment-
compatible disposal, allows the avoidance of potential negative effects on the environment and on human health, while favouring the recycling and
recovery of the component materials.
The unauthorised disposal of the product by the user entails the application of the sanctions contemplated under the national approval of Directives
2011/65/EU, 2008/98/EC and 2015/1127/EU.
