background image

4. READER OPERATION.

When the reader is ready, red LED shines to indicate that power is present.
When Mifare key is brought into reader working zone, its UID is read, and for 2.1.2 and 2.1.3 
modes, authorisation is also performed and additional codes are read from key memory. 
If reading is successful, the LED will momentarily turn green and a signal will sound. This will 
also cause transmission of: 
-  in 2.1.1 and 2.1.2 modes, the UID just read, and 
-  in 2.1.3 mode, the code from protected memory sector 
into controller, via iButton (Dallas Touch Memory), or Wiegand (-26/-34) protocols, depending on 
the configuration.

To configure the device, use the free software from 

M3NConf.zip

 archive.

The reader has internal and external LED and sound control.

Internal LED and sound control:

-  The red LED is ON when there is no key in reader working zone;
-  When a key enters the working zone, red LED goes OFF, green LED turns ON, and a short  
beep sounds;
-  While a known key is in working zone, no visual indication is present;
-  For 2.1.2 and 2.1.3 modes, when an unknown key enters the working zone, red LED goes   
momentarily OFF then back ON; no sound is emitted;
-  While an unknown key is in the working zone, red LED is ON.

External LED and sound control:

-  Comes from a controller, via external control pins (RED, GREEN, SND), or RS-485 
commands;
-  Turns on by a control signal applied on any of these pins.

Note:

 Regardless of external control signals, when a key is read, green LED will go ON and 

sound will beep for 0.1 second. For 2.1.2 and 2.1.3 modes, when an unknown key is presented 
into the working zone, red LED will shortly go OFF and back ON; no sound is emitted.

page

 3

Converter

Z-397 GUARD

+12 V 

DC 

power

Z-397

USB

RS 485

Matrix

 

III Net

D0

D1

RED

GND

SND

1.  SND  External sound control,
2.  D0  DATA0 output,
3.  GND  Ground, 
4.  D1  DATA1 output,
5.  RED  External red LED control,
6.  +12V  +12 V DC power input,
7.  GND  Ground,
8.  GREEN  External green LED control.

+12V

GREEN

GND

CLR

ADD

RS-485

ON

A

B

OFF

L

OAD

Figure 4.

 Connection layout.

A

B

MATRIX

 

III NET

www.ironlogic.

me

Summary of Contents for Matrix III NET






Reviews: