background image

1.

  GENERAL INFORMATION

Matrix

 

II EH

 RFID

 reader is used in Access Control Systems (ACS) to read contactless EM-

Marine Proximity and HID ProxCard II cards, and transmit the acquired card code via iButton 
(Dallas Touch Memory) or Wiegand 26 protocols. The reader allows for cards of both EM-Marine 
and HID 

ProxCard II

 standards to be used simultaneously.

2.  MOUNTING AND CONNECTION

The reader should be mounted on a flat surface, in a place allowing unimpeded proximity card 
access to the reader.
To mount the reader, perform the following sequence:
-  Mark and drill the mounting holes, per Fig. 1;
-  Connect wires to the reader socket,

 

according to layouts on Fig. 4 and 5.

Remove the thin tab in the reader case

, from the side where the cable must come out (Fig. 3), 

and
 

feed the cable through this hole. When power is connected to the reader, the red  LED will light 

up.
-  Mount the reader in the desired place and fix it with screws;
-  Close the reader holes with supplied plugs (Fig. 2)

Note 1:

 Do not install readers closer than 10 cm 

one 

from another.

Note 2:

 To achieve the specified reader distance from controller, a CAT5e UTP cable must be 

used (Fig. 5)

3.  OPERATION

The reader operation without external indication control:
1.  When power is supplied, in standby mode (no card present in the working zone), the LED
  

shines solid red.

2.  On card approach, its number is acquired. If succeeded, the LED turns green for a short
  

time, then switches off, and a short beep also sounds.

3.  While the card remains within the working zone, the LED stays off.
The external control for red and green colours of the LEDs and the buzzer is done by shorting 
corresponding terminals (LED R, LED G, BEEP) to the common ground terminal. The external 
indication control for one mode can be used with internal indication control for another; by default, 
both the LED and the buzzer are internally controlled. After external indication control signal has 
been activated (for example, for the LED), that indication goes under external control, while the 
other (in this case, the buzzer) remains under internal control.

page 1

MATRIX II EH

www.ironlogic.

me

 Matrix

 

II EH 

ACS RFID EM-Marine & HID ProxCard II 

Reader

 (125 kHz)

User Manual

Summary of Contents for Matrix II EH

Page 1: ...tall readers closer than 10 cm one from another Note 2 To achieve the specified reader distance from controller a CAT5e UTP cable must be used Fig 5 3 OPERATION The reader operation without external indication control 1 When power is supplied in standby mode no card present in the working zone the LED shines solid red 2 On card approach its number is acquired If succeeded the LED turns green for a...

Page 2: ... BEEP Figure 5 Connecting the reader to ACS controller Figure 4 mm mm mm mm mm LED Plugs CONNECTION LAYOUT Socket terminals 1 Power supply 12 V 2 Common ground 3 DATA0 output 4 DATA1 output 5 LED G external control for green LED 6 LED R external control for red LED 7 BEEP external control for the buzzer iButton DS1990A emulation iButton One time transmission ACS Controller Reader Common Common Com...

Page 3: ... 44 x 18 mm 5 OPERATING CONDITIONS Ambient temperature 30 40 C Humidity Up to 80 at 25 C Device specifications may differ from described in this manual when operating under non recommended conditions 6 PACKAGE CONTENTS MATRIX II EH Reader 1 Tabs 2 Screws 3x30 2 Wall Plugs 2 7 LIMITED WARRANTY Device is covered by limited warranty for 24 months from sale date The warranty becomes void if this Manua...

Page 4: ...uce the consumption of raw materials thus protecting the environment page 4 MATRIX II EH www ironlogic me 8 IRONLOGIC CONTACTS Headquarters RF Enabled ID Limited 34 Ely Place London EC1N 6TD UK E mail marketing rfenabled com Development and production AVS LLC 7 Bobruiskaya street Saint Petersburg 195009 Russian Federation E mail marketing rfenabled com Phone 78122411853 78125421185 www ironlogic r...

Reviews: