3.01 Introduction
Thanks for buying the IRIS606 Six Channel Video Switcher from
Iris Innovations!
The IRIS606 enables up to six on board CCTV cameras with a
composite video output to be viewed on up to two viewing
sources such as a dedicated video monitor or multi-functional
chart plotter display.
Easy to install, the IRIS606 has been designed to keep unsightly
cabling well out of the way, with a central control box into which
the video signals are terminated and a small, compact control
keypad that sits discretely at the helm for control.
The unit is supplied with a single IRIS560 control keypad and
other keypads can be added as desired.
3.02 Contents of Package
Please unpack your IRIS606 and check to make sure the
following items are included. If there are any items missing
please contact your Iris dealer:
1. IRIS606 Video Switcher
2. IRIS560 Control Keypad
3. 2m BNC~BNC Coaxial Video Cable - to connect the output of
the switcher to your monitoring source.
4. RJ45 Doubler - to facilitate connection of a second IRIS560
keypad is desired.
5. 1m Power cable with in-line 1A fuse.
6. BNC~RCA (Phono) Jack Adapter - for use if your viewing
device has a phono input
7. BNC~BNC Straight Adapter
3.03 Overview of Key Features
Here
ʼ
s a brief list os some of the IRIS606
ʼ
s Key Features:
•
6 Composite Video Outputs
•
2 Composite Video Outputs
•
Control via Remote Waterproof Keypad
•
Simple Operation and Setup
•
User Defined Sequence List
•
Low Power Consumption
•
Maximize your MFD
ʼ
s Video Display Capability
4.01 Connections.
Video:
Connect your camera inputs to the 6 female BNC inputs on the
side of the unit. Connect the video output cable (supplied) to
either of the 2 paralleled female BNC outputs.
Keypad:
Plug the RJ45 connector from your IRIS560 (also referred to as
DCS04 Keypad) into the panel mount socket labelled KEYPAD
on the side of the unit. Multiple keypads can be added. Refer to
the section 5.01 Adding Keypads for further details.
Power:
Connect the device using the power lead provided to a stable
+12VDC supply. The 2 power wires are colour coded RED for
+12VDC and BLACK for Ground. The RED +12VDC wire is
fitted with an in-line 1A fuse for additional protection.
4.02 Operation.
Camera Selection
To switch the desired video input, simply select the
corresponding numbered button on the keypad. The camera
selection will stay on the screen until a different input is
selected, or the sequence mode is activated.
Camera Sequence
To start the camera sequence, simply press the AUTO SEQ key
on the keypad. The switcher will now automatically switch
through each camera in the current sequence list.
4.03 Configuration.
Camera Sequence
In order to program the camera sequence list, follow the
procedure below:
•
Press and hold the AUX key for approximately 5
seconds until you hear a long beep. This enters
the camera into Configuration Mode.
•
Press each camera button to add it into the
sequence list. To increase the dwell time (the
time the camera stays on the screen before the
next camera is displayed whilst sequencing) for
each camera, press the camera button for each
second you wish to add. After 10 consecutive
presses (10 seconds) each subsequent button
press will add 5 seconds to the dwell time. The
maximum dwell time permitted per camera is
250 seconds.
•
Once camera selection and dwell time
programming is complete, press and hold the
ALT button once again until you hear a long
ʻ
beep
ʼ
, then release.
NOTE:
If at any time there is no programming activity for 10 seconds,
the switcher will return to it
ʼ
s operating mode with the previous
settings.
5
IRIS560 (DCS04) Keypad
