Irbit Motorcycle Factory Gear up 2005 Owner'S Manual Download

Page: 18 / 96

Clutch Control Lever

Font Brake Control Lever

Clutch control lever

. When the clutch lever is squeezed, the engine is disengaged from the

gearbox. When the lever is released, the engine and gearbox are engaged.

WARNING: M

AKE

SURE

FINGERS

ARE

NOT

POSITIONED

BETWEEN

HAND

CONTROL

LEVERS

AND

HANDLEBAR

GRIPS

OPERATION

VEHICLE

COULD

IMPAIRED

WARNING: B

EFORE

STARTING

ENGINE

ALWAYS

SHIFT

TRANSMISSION

NEUTRAL

PREVENT

ACCIDENTAL

MOVEMENT

WHICH

COULD

CAUSE

POSSIBLE

DAMAGE

MOTORCYCLE

AND

PERSONAL

INJURY

Caution: A

lways engage the clutch release lever when shifting. Serious internal damage may

result to the transmission if the clutch release lever is not engaged.

Front brake control lever

When the lever is squeezed, the front wheel brake is actuated. The

front brake should be used together with rear brake.

When the brake lever is squeezed, the stop signal lights are switched on.

Summary of Contents for Gear up 2005

































































































Search results

Summary of Contents for Gear up 2005

Reviews:

Related manuals for Gear up 2005

Brands by name

Popular brands

Irbit Motorcycle Factory Gear up 2005, Owner'S Manual

Search results

Summary of Contents for Gear up 2005

Reviews:

Related manuals for Gear up 2005

Brands by name

Popular brands