2. Warnings and Safety information
continued
Medical warnings
continued
DO NOT
use if you have used any medicines or
products that have photosensitising properties
in the last 3 months. Appendix A on page 26
contains a list of common medicines and
products that may cause photosensitivity.
If you have a medical condition or you are
taking medicines and are unsure about
using the Boots Smooth Skin system,
seek medical advice before use.
Electrical warnings
The Boots Smooth Skin system is designed
for use in the UK and elsewhere in the world
l]ZgZi]ZbV^chhjeeankdaiV\Z^h&%%Kid')%K
68*%$+%=o#JhZdcdi]ZghjeeankdaiV\ZhbVn
result in damage to the equipment.
After 50 shots in quick succession there is an
automatic cooling delay of about a minute where
the system will not respond—this is absolutely
normal and nothing to worry about. This cooling
delay is indicated by the ‘READY’ light flashing.
When it glows constantly the unit is ready to
use again.
After 200 shots within a 30 minute period there
will be a 5 minute automatic cooling delay where
the unit will not respond—this is absolutely
normal and nothing to worry about. This cooling
delay is indicated by the ‘READY’ light flashing.
When it glows constantly the unit is ready to
use again.
The unit will automatically go into STANDBY if
not used for approximately 1 minute, and the
green STANDBY light will come on. To use again
press the STANDBY button.
Check that the voltage rating marked on the
rating plate of the Boots Smooth Skin system
corresponds to the actual supply voltage.
Check that your Boots Smooth Skin system is
in good condition. Regular after use cleaning is
essential to maintaining the Boots Smooth Skin
system in optimum working condition.
DO NOT
use if damage is found e.g. cracked
case, handset cable damage (internal wires
visible), cracked or badly chipped glass on the
handset etc. Internal parts contain energy levels
VcYkdaiV\Zhi]ViVgZ]VoVgYdjh#
DO NOT
use the Boots Smooth Skin system
in a bathroom or near sinks or other vessels
containing water. If the Boots Smooth Skin
system becomes wet it should not be used.
DO NOT
coil the power cable around the power
supply during storage; this can lead to cable
damage and early failure.
DO NOT
pull the handset cable tight, bend it
through very sharp angles or wrap it around the
unit for storage, this may cause cable damage
and early cable failure.
DO NOT
use if either the base unit or hand unit
become hot to touch.
DO NOT
dismantle; the Boots Smooth Skin
hnhiZb XdciV^ch cd jhZg"hZgk^XZVWaZ eVgih
and internal energy levels and voltages
VgZ]VoVgYdjh#
DO NOT
use a power supply or any other
accessory unless they are specifically approved
and supplied for use with the Boots Smooth
Skin system. Use of accessories, which are not
approved, may be dangerous.
The Boots Smooth Skin system is designed to
operate between 15 – 30˚C.
ALWAYS
unplug the Boots Smooth Skin system
when not in use.
9
8
3. Getting ready for a treatment
The Boots Smooth Skin system consists of three
parts; the power supply, the base unit and the
handset. Each time you use the Boots Smooth
Skin system, inspect all parts of the system
for damage. If damage is found it should not
be used.
Set up the Boots Smooth Skin
system
Place the base unit on a firm, flat surface.
The handset should be plugged into the base
unit taking care not to damage the retaining
clips and to fit the plug the correct way round.
1. Power Supply
2. Base Unit
3. Handset
Retaining clips
one on each side
DO NOT
force the plug into the socket as this
may cause damage.
Gathering together the essentials
you may need
Before starting to use Boots Smooth Skin
system you may find it useful to gather together
some helpful bits and pieces.
You will need:
7ddihHbddi]H`^c6Xi^kVidg<Za
We recommend you keep this in the fridge so it’s
more cooling when you apply it to the skin.
We recommend you have to hand:
HE;(%[gV\gVcXZ"[gZZhjciVcadi^dc
;gV\gVcXZ"[gZZbd^hijg^h^c\XgZVb
L]^iZZnZa^cZgeZcX^a
L]^iZXVgYdgl]^iZhi^X`naVWZah
HeVijaV
I^hhjZh
IdlZa
