manualshive.com logo in svg

iPECS iPECS-LIK, Feature Description & Operation

The iPECS iPECS-LIK Installer's Manual is a comprehensive guide that allows you to easily set up and customize your iPECS-LIK system. It provides step-by-step instructions and detailed illustrations, ensuring a hassle-free installation process. Download this manual for free from our website and empower yourself to maximize the full potential of your iPECS-LIK product.

Share
Download
background image

iPECS-LIK 
Feature Description & Operation Manual 

Issue 6.0d1 

 

 

432 

8.18 SIP VIRTUAL CO LINE (VCOL) 

Description 

Virtual channel without DSP usage for SIP trunk. 

Voice and Video is direct between end sides. 

Support only DTMF type 

Operation 

1. Incoming call from SIP trunk to system 

Voice or Video call from external via SIP Virtual CO line. 

2. Make outbound call from system to SIP trunk 

Seize SIP Virtual CO line and make Voice or Video call to SIP trunk. 

Conditions 

1. Support only Outband DTMF type (SIP Info Message). 

2. Tone detection is not supported 

Programming 

1. Create new SIP Virtual CO lines (VCOL) 

−  System ID & Numbering Plans / PGM 101 

‘Virtual Registration’ 
Device ID : CO / VOIM8 or VOIM24 (you can specify number of channel by 
‘Max Port’) 
MAC Address : check disable and it will be virtually created automatically 
Data : Max port / Virtual SIP ON or not 

−  Max Port : number of channels y 
−  Virtual SIP : ‘should be checked’ 

 

2. Replace a normal SIP CO lines to VCOL (purpose : remove a physical VOIM to 

replace it as a virtual) 

−  the slot should be in ‘Out Of Service’ state 

(you can force that to ‘Out Of Service’ state in PGM 103 by click ‘CO Gateway’, 
check ‘SVC’ and save) 

−  SIP Data / PGM 133 : set ‘Virtual SIP Channel Mode’ to ‘Yes’ 

(state is set to activated automatically) 
(‘RTP Diversion Method’ is automatically set to ‘Non-Recursing’) 

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS-LIK

THOMSON TG782 Setup And User Manual preview
TG782
Brand: THOMSON Pages: 90
TDL Triton Gateway Installation Procedures Manual preview
Triton Gateway
Brand: TDL Pages: 47
Juniper VGW VIRTUAL GATEWAY Datasheet preview
VGW VIRTUAL GATEWAY
Brand: Juniper Pages: 6
B&B Spectre LTE Quick Start Manual preview
Spectre LTE
Brand: B&B Pages: 2
Moxa Technologies NPort 6110 Quick Installation Manual preview
NPort 6110
Brand: Moxa Technologies Pages: 2
SenseNet control4all Setup preview
control4all
Brand: SenseNet Pages: 11
ZyXEL Communications P-661HW-D Series Support Note preview
P-661HW-D Series
Brand: ZyXEL Communications Pages: 146
SharkRF openSPOT3 User Manual preview
openSPOT3
Brand: SharkRF Pages: 131
Aaeon SRG-APL User Manual preview
SRG-APL
Brand: Aaeon Pages: 26
HMS Intesis KNX User Manual preview
Intesis KNX
Brand: HMS Pages: 26
Nokia BGW320 User Manual preview
BGW320
Brand: Nokia Pages: 3
Nokia CC500 - VPN - Gateway Connection Manual preview
CC500 - VPN - Gateway
Brand: Nokia Pages: 11
Nokia 10i Installation Manual preview
10i
Brand: Nokia Pages: 48
Nokia 50i Installation Manual preview
50i
Brand: Nokia Pages: 58
Nokia AD-42W Manual preview
AD-42W
Brand: Nokia Pages: 62
Nokia 100i Installation Manual preview
100i
Brand: Nokia Pages: 72
Nokia FastMile User Manual preview
FastMile
Brand: Nokia Pages: 87
Nokia 3TG-01275-AAAA-TCZZA Operator'S Manual preview
3TG-01275-AAAA-TCZZA
Brand: Nokia Pages: 96

Brands by name

Popular brands

Load more brands