iPECS iPECS-LIK Feature Description & Operation Download Page 422

Page: 422 / 447

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

409

8.3 MAKE CALL

Description

There are three types of call setup

– Station Call, CO Call, System Call Feature Implementation.

Operation

Making Station Call Setup

1. Dial Station Number.

If ‘Dial Digit Map’ is programmed, SIP Phone will send call setup immediately.

If ‘Dial Digit Map’ is not programmed, press the

[SEND]

button or “#” key for send

out call setup.

Making CO Call Setup

1. CO Access Code + Dial

[SEND]

ex) CO Access Code “9”, Dial Number ‘450-4500’,
dial ‘94504500’ and press

[SEND]

or “#” button

NOTE

If you program ‘Second Dial Tone Digit Map’ on SIP Phone, you will hear self dial tone
from SIP Phone.

2. CO Access Code +

[SEND]

after hearing CO dial tone, press Dial Number
ex) CO Access Code “9”, Dial Number ‘450-4500’,
dial “9” and press

[SEND]

or “#”

hear CO dial tone from system
dial ‘4504500’

Making System Call Feature Setup

1. System Call Feature by Numbering Code : System Numbering Plan (PGM106-109)

2. Enblock Dialing : System Call Feature numbering code + data +

[SEND]

button.

3. Supported Call Features by Numbering are,

Internal Page Zones

Internal All Call Page

Meet Me Page

Internal All Call Page

Meet Me Page

Internal All Call Page

External Page Zone

External All Call Page

All Call Page

SMDR Account Code Enter

SLT Last Number Redial

Do-Not-Disturb(DND)

Call Forward

Speed Dial Program

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS-LIK

Reviews:

Related manuals for iPECS-LIK

Brands by name

Popular brands

iPECS iPECS-LIK, Feature Description & Operation

Search results

Summary of Contents for iPECS-LIK

Reviews:

Related manuals for iPECS-LIK

Brands by name

Popular brands