iPECS iPECS-LIK Feature Description & Operation Download Page 299 | Manualshive

Page: 299 / 447

background image

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

286

4.4 CO/IP LINE PRESET FORWARD

Description

Each CO/IP Line can be assigned a Ring-No-Answer Preset Forward destination. An incoming
call on the CO/IP line will be routed to the defined ring destination. At expiration of the CO/IP
Line Preset No Answer Forward timer, the call is forward to the defined Preset Forward
destination, which is an index to the ICLID Ring Assignment Table.

The destination can be a station or station group including an adjunct Voice Mail. When the call
is forwarded to an adjunct Voice Mail group, a predefined Voice Mail Id (VMID) will be sent to
the VM system to identify the Mailbox to receive the call.

Operation

System

Operation of this feature is automatic.

Conditions

1. CO/IP line Preset Forward is disabled for calls initially routed to a station group.

2. CO/IP line Preset Forward will override Call Forward No-Answer at a station.

3. CO/IP line Preset Forward is disabled if the Preset Forward Timer is set to 0.

4. The CO/IP line Preset Forward destination cannot be the VMIM/VSF group.

Programming

CO/IP

1 CO Preset Forward, Forward timer (PGM 147-Btn 1)

2 CO Preset Forward, Ring Table Index (PGM 147-Btn

2)

3 CO Preset Forward, VMID (PGM 147-Btn 3)

ISDN & ICLID

1 ICLID Ring Assignment Table (PGM 204)

Related Features



Call Forward



ICLID Call Routing

Hardware

«
...
297
298
299
300
301
...
»

Summary of Contents for iPECS-LIK
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS-LIK

Anybus Modbus-TCP/RTU Gateway

Brand: HMS Pages: 20

460PBSDFM-N70PB

Brand: RTA Pages: 73

Brand: HW Group Pages: 19

IGW1111-3IN1-DB

Brand: 3onedata Pages: 3

Brand: Ingics Pages: 12

Brand: Gree Pages: 12

V-NET PLNWKB000

Brand: LG Pages: 19

Brand: LG Pages: 23

V-NET PLNWKB000

Brand: LG Pages: 183

Brand: LG Pages: 11

Brand: Technicolor - Thomson Pages: 21

Brand: TENETICS, LLC Pages: 12

WPG-150 - Wireless Video Extender

Brand: ViewSonic Pages: 3

Brand: Planet Networking & Communication Pages: 19

Meshlium Xtreme

Brand: Libelium Pages: 214

CT-100-SPLIT ROW

Brand: enphase Pages: 2

Brand: enphase Pages: 2

PacketStar AC 60

Brand: Lucent Technologies Pages: 410

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands