IONIT Networks LLC
•
5600 Post Rd, Suite 114, Unit 225
•
East Greenwich, RI 02818
•
(401) 244-7404
•
www.ionitnetworks.com
Installation Instructions for
ION-9100 Remote Tank Level Display
Version 1.1 – 03/21/2016
How To Read My Remote Display
Reading Tank Level
Number and Type of LED Segments
Fuel level based on your tank’s capacity in gallons
10 GREEN Solid LEDs
Full Tank - 95% to 100% full
9 GREEN Solid LEDs
85% to 95% full
8 GREEN Solid LEDs
75% to 85% full
7 GREEN Solid LEDs
65% to 75% full
6 GREEN Solid LEDs
55% to 65% full
5 GREEN Solid LEDs
45% to 55% full
4 GREEN Solid LEDs
35% to 45% full
3 GREEN Solid LEDs
25% to 35% full
2 GREEN Solid LEDs
20% to 25% full
2 YELLOW Solid LEDs
TANK LEVEL WARNING – 15% to 20% full
1 YELLOW and 1 RED Solid LED
TANK LEVEL WARNING – 10% to 15% full
1 RED Solid LED
TANK LEVEL WARNING – 5% to 10% full
1 RED Flashing LED
LOW TANK ALERT – less than 5% full
Reading Diagnostics
Type of LED Segments
Fuel level based on your tank’s capacity in gallons
Flashing alternate RED LEDs
9100 Remote Tank Display is not associated (“paired”) with your
9071 fluid level sensor
Flashing GREEN LEDs
9100 is paired to a 9071 fluid level sensor, but the 9071 sensor is in
Hibernate mode
Solid YELLOW LEDs instead of GREEN LEDs for tank level
Replace Battery in your 9071 fluid level sensor. Indicates battery is
below 2.4 Volts. When tank level display is in TANK LEVEL
WARNING range (see above table), this low battery indicator will
not be visible as it will overlap with the TANK LEVEL WARNING
display.
Solid RED LED above Tank Level LEDs
Indicates the 9100 has not received a transmission from its paired
9071 in over 6 hours
Animating YELLOW LEDs with RED LED on top
Received Signal Strength Indicator (RSSI) display (see table below)
Flash All LEDs RED
Indicates 9100 just received a transmission from the paired 9071,
or is repeating a transmission.
Reading Received Signal Strength Indicator (RSSI)
Number and Type of LED Segments
Fuel level based on your tank’s capacity in gallons
9 1 RED top LED
over 95% signal strength
8 1 RED top LED
over 85% signal strength
7 1 RED top LED
over 75% signal strength
6 1 RED top LED
over 65% signal strength
5 1 RED top LED
over 55% signal strength
4 1 RED top LED
over 45% signal strength
3 1 RED top LED
over 35% signal strength
2 1 RED top LED
over 25% signal strength
1 1 RED top LED
over 15% signal strength
1 RED LED
LOW SIGNAL – under 15% signal strength
IMPORTANT INFORMATION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Do not change or modify the device. Any modifications will void your authority to operate the equipment.
