IOGear M1161 Installation Manual Download Page 8 | Manualshive

Page: 8 / 52

IOGear M1161 Installation Manual Download Page 8

8

Installation

Wireless Setup with WPS

Step 1:

Power on your Universal WiFi Adapter using

either

of these methods:

• Connect the mini-USB cable to a device that provides Type A USB connection. Make sure that the device

where you connect the USB cable is powered on.

• Connect the WiFi adapter to an electrical outlet with the included power adapter.

Note: It will take about 50 seconds to complete the boot-up sequence. When complete, PWR (power) LED
will be active, and the WLAN Activity LED will be blinking to show the WLAN interface is enabled.

Step 2:

Use the included RJ-45 Ethernet cable to connect the WiFi adapter with your device such as

Blu-ray player, HDTV, or game console.

Step 3:

Refer to your wireless router’s user manual to enable the WPS function, then press “WPS” button

on the top of WiFi adapter.

Your installation is complete. If asked for the type of connection, make sure “WIRED” is selected on your
device.

«
...
6
7
8
9
10
...
»

Summary of Contents for M1161





















































Reviews:

No comments