background image

                                                Important Safety Instructions 

True Online 6-20k UPS User Manual

 

IMPORTANT SAFETY INSTRUCTIONS 

SAVE THESE INSTRUCTIONS 

This manual contains important safety instructions. Read all safety and operating 

instructions before operating the uninterruptible power systems (UPS). Adhere to all 

warnings on the unit and in this manual. Follow all operating and user instructions. This 

equipment can be operated by individuals without previous training. 

This product is designed for commercial/industrial use only. It is intended for use with lift 

support and other designated “critical” devices. Maximum load must not exceed that shown 

on the UPS rating label. The UPS is designed for data processing equipment. If uncertain, 

consult your dealer or local representative. 

This UPS is designed for use on a properly grounded (earthed), 220/230/240VAC, 50 or 

60Hz supply. The factory default setting is 220VAC/50Hz. Installation instructions and 

warning notices are in this manual. 

The UPS 06-20@220/230/240VAC is designed for use with a three-wire input (L,N,G). 

 WARNING 

THE BATTERY CAN PRESENT A RISK OF ELECTRICAL SHOCK AND 

HIGH SHORT CIRCUIT CURRENT. FOLLOWING PRECAUTIONS 

SHOULD BE OBSERVED BEFORE REPLACING THE BATTERY. 

z

 

Wear rubber gloves and boots. 

z

 

Remove rings, watches and other metal objects. 

z

 

Use tools with insulated handles. 

z

 

Do not lay tools or other metal objects on the batteries. 

z

 

If the battery is damaged in any way or shows signs of leakage, contact your local 

representative immediately. 

z

 

Do not dispose of batteries in a fire. The batteries may explode. 

z

 

Handle, transport and recycle batteries in accordance with local representative. 

WARNING 

ALTHOUGH THE UPS HAS BEEN DESIGNED AND MANUFACTURED 

TO ENSURE PERSONAL SAFETY, IMPROPER USE CAN RESULT IN 

Summary of Contents for HT1106L








































Reviews: