117 Channels mode
CH
Function
value
Details
1
Pan movement
0-255
0~540 degree
Unlimited Pan
0-55
Tilt non movement
2
56-155
Pan unlimited clockwise rotate slow to fast
movement
156-255
Pan unlimited reversely rotate slow to fast
3
Pan fine
0-255
16 bit Pan fine adjustment
4
Tilt
0-255
0~270 degree
Unlimited Tilt
0-55
Pan non movement
5
56-155
Tilt unlimited clockwise rotate slow to fast
movement
156-255
Tilt unlimited reversely rotate slow to fast
6
Tilt fine
0-255
16 bit Tilt fine adjustment
7
Pan/Tilt speed
0-255
From fast to slow
8
Dimmer
0-255
Linear dimmer from dark to bright
0-3
No function
9
Strobe
4-95
Strobe with the same step from slow to fast
96-176
Random strobe
177-255
Thunder strobe
10
R1 dimmer
0-255
LED 1 Red dimmer from dark
to bright
11
G1 dimmer
0-255
LED 1 Green dimmer from dark to bright
12
B1 dimmer
0-255
LED 1 Blue dimmer from dark to bright
13
W1 dimmer
0-255
LED 2 white dimmer from dark to brigh
……
……
……
……
……
……
……
……
106
R25 dimmer
0-255
LED 25 Red dimmer from dark to bright
107
G25 dimmer
0-255
LED 25 Green dimmer from dark to bright
108
B25 dimmer
0-255
LED 25 Blue dimmer from dark
to bright
109
W25 dimmer
0-255
LED 25 white dimmer from dark to bright
Effect show of
0-89
Effect show of numbers from 0 to 9
110
numbers and
90-233
Effect show of punctuations
punctuations
234-235
Running water effect
111
Effect show of
0-234
Effect show of letters from A to Z
letters
234-235
Running water effect
112
Effect show of
0-234
Effect show of static gobos
static gobos
234-235
Running water effect
113
Color of letters
0-255
Color choice for the letters
114
Dynamic gobos
0-234
Effect show of dynamic gobos
show
234-235
Running water effect
115
Speed of effects
0-255
From fast to slow
0-49
No function
50-74
Numbers and punctuations show(Against CH
12)
116
Macro Function
75-99
Letters show(Operate against CH 13)
100-124
Static gobos show(Operate against CH 14)
125-149
Dynamic gobos show(Operate against CH 16)
150-199
Auto Run
200-255
Sound activated
117
Reset
0-250
No function
251-255
Reset within 3 seconds
2. Safety Instructions
This device has left the factory in perfect condition. In order to maintain this condition and to ensure
a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this user manual.
If the device has been exposed to temperature changes due to environmental changes, do not
switch it on immediately. The arising condensation could damage the device. Leave the device
switched off until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be earthed.
The electric connection must carry out by qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would be the
case, replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle
the power cord by the plug. Never pull out the plug by tugging the power cord.
During initial start-up some smoke or smell may arise. This is a normal process and does
not necessarily mean that the device is defective, it should decrease gradually. Please don't
project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm distance with wall
for smooth air flow, so there should be no shelter for fans and ventilation for heat radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by
the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
.9.
.2.
