Connect the cables from the Quattro LNB to the input connectors marked with LNB V/L, V/H, H/L and
H/H inputs (pay attention to identification of the Quattro LNB connectors).
V/L
V/H
H/L
H/H
Satellite - Input
H/H
H/L
V/H
V/L
Satellite - loop-through output
TM
Unicable cascadable switch 4 User Bands, 1 Legacy port
IDLP-USW112-CUO1O-4PP
User Bands :
0 : 1210MHz
1 : 1420MHz
2 : 1680MHz
3 : 2040MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: -3dB
Unicable Out
Legacy Out
The Unicable output allows to connect up to 4 receiver tuners – each needs to be allocated one of the
4 user bands supported by the multiswitch.
Each receiver tuner is assigned with 1 out of 4 communication channel frequencies (user band). The
frequencies are listed on the product sticker:
V/L
V/H
H/L
H/H
Satellite - Input
H/H
H/L
V/H
V/L
Satellite - loop-through output
TM
Unicable cascadable switch 4 User Bands
IDLP-USW1O2-CUO1O-4PP
User Bands :
0 : 1210MHz
1 : 1420MHz
2 : 1680MHz
3 : 2040MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: -3dB
Unicable Out
V/L
V/H
H/L
H/H
Satellite - Input
H/H
H/L
V/H
V/L
Satellite - loop-through output
TM
Unicable cascadable switch 4 User Bands, 1 Legacy port
IDLP-USW112-CUO1O-4PP
User Bands :
0 : 1210MHz
1 : 1420MHz
2 : 1680MHz
3 : 2040MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: -3dB
Unicable Out
Legacy Out
For optimized performance, please follow the recommendations below:
1. use the highest frequency for a wall socket located the nearest to the multiswitch and use the
lowest frequency for wall socket located farest to the multiswitch.
2. If you install less than 4 receiver tuners, use the lowest frequencies first. We also recommend
to keep record of the user bands allocated to the different connections as these user bands will
then have to be set in the receiver. The satellite receivers connected to the multiswitch have to
be Unicable-compatible (usually marked with Unicable™ logo).
Note: Loopthrough outputs that are not used should be terminated with 75ohm DC-blocked
terminations.
Safety
Never open a powered product. This may result in electrical hazard.
Never work on the product, TV set or other powered devices during or before a storm. A lightning
strike into the antenna may cause dangerous overvoltage over the product’s metallic/conductive
parts.
Make sure the local electricity network corresponds to the operating voltage of the AC/DC adaptor.
If the products gets into contact with liquid it must be disconnected from the main power.
It is recommended to disconnect the product from the main power if it is not used for long periods of
time.
When disconnecting the product don’t pull the cable but the plug to prevent damage of the cable
(wobbly plugs and outlets result in fire risk).
The product shall be serviced by qualified experts only.
Thank you for purchasing Inverto’s advanced Unicable multiswitch and we are certain it will meet your
expectations. Before installing and operating the product, please read the following instructions and
recommendations. We suggest that you keep this manual for future use.
Warranty
This Unicable multiswitch is designed for the distribution of satellite and terrestrial television and radio
signals in home installations. The warranty does not apply for products used for other purposes than
those specified herein. The user/installer shall be responsible for any damage incurred as a result of
not using the product according to the instructions in this manual.
Installation location
The product shall be installed on a wall or other hard inflammable surface.
The product shall be in no case held only with the connected cables.
Place the product in a dry environment where it is not exposed to rain or running water.
Do not install the product close to heat sources or in places exposed to direct sunlight.
Product installation
The following diagram may assist you when drilling the holes:
122
114.50
V/L
V/H
H/L
H/H
Satellite - Input
H/H
H/L
V/H
V/L
Satellite - loop-through output
TM
Unicable cascadable switch 4 User Bands
IDLP-USW1O2-CUO1O-4PP
User Bands:
0 : 1210MHz
1 : 1420MHz
2 : 1680MHz
3 : 2040MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: -3dB
Unicable Out
To connect the product inputs and outputs use high-quality
coaxial cables designed for satellite reception and
F-connectors. Use a high-shielding coaxial cables with
minimum 90dB.
If you use wall sockets to loopthrough the 4 user bands, make
sure the wall sockets were designed for satellite reception
compatible with Unicable technology and allows bidirectional
signal propagation.
The switch may be powered by the connected Unicable
STBs directly or through the supplied Power Inserter and
AC adaptor. For long cable installations, it is recommended
t o
use the supplied Power Inserter and the AC/DC adaptor in order to ensure proper and stable input volt-
age level. The power inserter shall be connected over the Unicable port.
The following diagram describes the installation configurations supported by the product:
Quattro
LNB 1
Terminated
Outputs
x4 User bands
UB 0 UB
1
UB 2 UB
3
Power
inserter
x4 User bands
UB 0 UB
1
UB 2 UB
3
V/L
V/H
H/L
H/H
Satellite - Input
H/H
H/L
V/H
V/L
Satellite - loop-through output
TM
Unicable cascadable switch 4 User Bands
IDLP-USW1O2-CUO1O-4PP
User Bands:
0 : 1210MHz
1 : 1420MHz
2 : 1680MHz
3 : 2040MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: -3dB
Unicable Out
V/L
V/H
H/L
H/H
Satellite - Input
H/H
H/L
V/H
V/L
Satellite - loop-through output
TM
Unicable cascadable switch 4 User Bands
IDLP-USW1O2-CUO1O-4PP
User Bands:
0 : 1210MHz
1 : 1420MHz
2 : 1680MHz
3 : 2040MHz
Satellite inputs: IF 950-2150MHz
Satellite Loop-Through loss: -3dB
Unicable Out
AC/DC Input
2
3
