INSTALLATION PROCEDURE
CAUTION
CAUTION
Fig.8
Fig.9
Fig.10
Fig.11
Fig.12
Diameter
φ
ĭĭ
a
Table 1
4.Back cover installation
6.Front cover installation
86 Electrician
box
Embedded 86 electrician
box wiring
1. Use straight head screwdriver to insert into the buckling position in the bottom
of wire controller, and spin the screwdriver to take down the back cover. (Pay
attention to spinning direction, otherwise will damage the back cover!) (Fig.5)
2. Use three GB950-86 M4X20 screws to directly install the back cover on the
wall. (Fig.6)
3. Use two M4X25 GB823-88screws to install the back cover on the 86 electrician
box, and use one GB950-86 M4X20 screws for fixing on the wall. (Fig.7.1)
4. Adjust the length of two plastic screw bars in the accessory to be standard
length from the electrical box screw bar to the wall. Make sure when install the
screw bar to the electrical box screw bar, make it as flat as the wall. (Fig.7.2)
5. Use cross head screws to fix the wire controller bottom cover in the electric
control box through the screw bar. Make sure the wire controller bottom cover is
on the same level after installation, and then install the wire controller back to the
bottom cover.
6. Over fasten the screw will lead to deformation of back cover.
WIRED REMOTE CONTROLLER INITIAL PARAMETER SETTING
Wired remote controller initial parameters setting:
1.Change the related functions of the controller through adjusting the initial parameters, details refer to table 1.
2.The wired remote controller initial parameter include two codes “XY”, the first code “X” means function class, the second code “Y” means detailed configuration of this function.
3.Setting method:
ǂ
Ś
Simultaneously long press “Mode” and “Fan” button of the wired remote controller for 5 seconds to enter the parameter setting state;
ś
The value of this first code “X” is “0”, press the temperature setting button and to adjust the second code value;
Ŝ
After setting the second code value, press
button to switch the first code to the next value;
ŝ
When the first code value is “6”, press
button again to exit the parameters setting.
4.The parameters setting function only under the situation which need to adjust the default functions’ setting states; otherwise there is no need to do the setting.
After adjusting the front cover and then buckle the front cover; avoid clamping the communication switching wire during
installation. (Fig.11)
Correct install the back cover and firmly buckle the front cover and back cover, otherwise will make the front cover drop
off. (Fig. 12)
Avoid the water enter into the wired remote controller, use trap and putty to seal the connectors of wires during wiring
installation. (
Fig.10
)
When under installation, reserve certain length of the connecting wire for convenient to take down the wired remote
controller while during maintenance.
CAUTION
5.Wiring
B.Shielded wiring
A.Wiring, three outletting positions
Upper left wire outlet
Top side
wire outlet
Left middle
side wire
outlet
Cutting place of top
side wire outlet
Cutting place of upper
left wire outlet
Cutting place of left
middle side
wire outlet
Wiring
hole
Wiring through the wall
Wall hole and wiring hole
Putty
Putty
Putty
Trap
Trap
Trap
First code
Second code
Function
Cool-only/ Cool-Heat
selection
Cool-Heat
(Default)
Cool-only
Indoor unit
communication
address setting
Power-off memory
Filter cleaning
reminding
Remote receiving
function
Centigrade/ Fahrenheit
display
Fahrenheit
Centigrade
(Default)
None
None
Yes
(Default)
Yes
(Default)
None
Cancel the
reminding
function
1250 hours
2500 hours
(Default)
5000 hours
10000 hours
Buckling position
Back cover
Front cover
Straight head screwdriver
Fig.5
Screw hole installed on
the wall,use three
GB950-86 M4X20
Screw hole fixed on
the wall,use one
GB950-86 M4X20
Screw hole installed
on 86 Electrician box,
use two
0;
*%
Fig.7.1
Fig.6
Fig.7.2
86 Electrician box
Signal switching wires
Back cover
Yes
(Default)
)RU FRROLQJ RQO\ RSHUDWLRQV
please do corresponding settings
as described .
Note:
