background image

3

Working principle and special functions for cooling

Working principleand special functions for heating

Defrosting:

*

When outdoor temperature is low but high humidity, after a long while running, frost will

form on outdoor unit, that will effect the heating effect, at this time, the auto defrosting

function will act, the heat running will stop for 8-10mins.

*

During the auto defrosting, the fan motors of indoor unit and outdoor unit will stop.

*

During the defrosting, the indoor indicator flashes, the outdoor unit may emit  vapor.

This is due to the defrosting, it isn't malfunction.

*

After defrosting finished,the heating will recover automatically.

Notices for use

Air conditioner absorbs heat in the room and transmit to outdoor and discharged, so that
indoor ambient temperature decreased, its cooling capacity will increase or decrease by

outdoor ambient temperature.

If the unit is running in COOL mode and in low temperature, there will be frost formed on
the heat exchanger, when indoor heat exchanger temperature decreased below 0  , the
indoor unit microcomputer will stop compressor running and protect the unit.

Principle:

*

Air conditioner absorbs heat from outdoor and transmits to indoor, in this way to increase

room temperature. This is the heat pump heating principle, its heating capacity will be

reduced due to outdoor temperature decrease.

*

If outdoor temperature becomes very low, please operate with other heating equipments.

Principle:

Anti-freezing function:

Anti-cool wind function:

In "Heat" mode, under the following three kinds of state, if indoor heat exchanger doesn't 

arrive at certain temp., indoor fan will not act, in order to prevent cool wind blowing(within

2 mins):
1. Heating starts. 2.After Auto Defrost finished. 3.Heating under the low temperature.

The operating temperature range (outdoor temperature) for cooling unit is 

-7

~ 43

℃;

for cooling and heating unit is 

 -7

~4

3

.

Working temperature range

Maximum cooling

Minimum cooling

Maximum heating

Minimum heating

Indoor sideDB/WB(

o

C)

Outdoor sideDB/WB(

o

C)

32/23
21/15

27/---
20/---

43/26

21/

24/18

-5/-6

Summary of Contents for B2VI-09
































Reviews: