background image

 

27

 

 

Danger of breaking down in adverse weather conditions, i.e. extreme cold, in an isolated 
area! 

• 

If you are a user with severely limited mobility, we advise that in the case of adverse weather 
conditions DO NOT attempt a journey without an accompanying attendant! 

Danger of injury if your foot slides off the footrest and gets caught underneath the 
wheelchair when it is in motion! 

• 

Make sure each time before you drive the wheelchair that your feet are squarely and securely 
in place on the footplates, and that both legrests are properly locked into place. 

Danger of injury if you collide with an obstacle when driving through narrow passages 
such as doorways and entrances! 

• 

Drive through narrow passages in the lowest driving mode and with due caution. 

If your power wheelchair has been fitted with angle-adjustable legrests, there is a danger 
of personal injury and damage to the wheelchair if you drive the wheelchair with the 
legrests raised! 

• 

To avoid unwanted displacement of the wheelchair centre of gravity to the front (especially 
when travelling downhill) and in order to avoid damage to the wheelchair, angle-adjustable 
legrests must always be lowered during normal travelling. 

 

 

 

 

CAUTION: Danger of tipping! Anti tip wheels (stabilisers) are only effective on firm 
ground! They sink in on soft ground such as grass, snow or mud if the mobility device 
rests itself on them. They lose their effect and the mobility device can tip over. 

• 

Only drive with extreme care on soft ground, especially during uphill and downhill journeys. In 
the process pay increased attention to the tip stability of the mobility device. 

 

Summary of Contents for Mistral Plus













































































































Reviews: