Invacare HomeFillII AW Service Manual Download Page 83

Page: 83 / 104

SECTION 12—WIRING ASSEMBLIES

Part No 1154316

HomeFill

II AW Compressor

FIGURE 12.3

Replacing Bleed Resistor Assemblies - Units Manufacture Before 7/3/06

Units Manufacture After 7/3/06

NOTE: The bleed resistors in this view are for units made before 7/3/06. On units made after
7/3/06, bleed resistors are on the PC board with a separate wiring harness.

Replacing HFII Assembly Wire Harness

NOTE: For this procedure, refer to FIGURE 12.4 on page 84.

1. Remove the cabinet. Refer to Removing/Installing the Cabinet on page 25.

2. Remove the control panel. Refer to Removing/Installing Control Panel on page 29.

3. Note the orientation of the connectors on the power inlet (Detail “A”).

4. Disconnect the two connectors from the power inlet.

5. Note the orientation of the two connectors on the hour meter (Detail “A”).

6. Disconnect the two connectors from the hour meter.

Bleed Resistor

Assembly 1

Motor Assembly

Grounding Clip

Bleed Resistor

Assembly 2

DETAIL “A”

DETAIL “B”

DETAIL “C”

Power Inlet

Bleed Resistor

Assembly 1

Control Panel

Bleed Resistor

Assembly 2

Summary of Contents for HomeFillII AW









































































































Search results

Summary of Contents for HomeFillII AW

Reviews:

Related manuals for HomeFillII AW

Brands by name

Popular brands

Invacare HomeFillII AW, Service Manual

Search results

Summary of Contents for HomeFillII AW

Reviews:

Related manuals for HomeFillII AW

Brands by name

Popular brands