background image

Open-X™ 8M Development Kit based on the NXP i.MX8™ Processor User Guide  Version 1.0 

16

 

Copyright Intrinsyc Technologies Corporation 

 

Open-X 8M Carrier Board Expansion Connectors 

Table 3.8.2-1 lists the connectors, expansions and their usages on the carrier board: 
 

Table 3.8.2-1 Carrier Board Expansion options and their usage 

Domain 

Description 

Specification 

Usage 

Power 

AC / Barrel charger 

12 V DC Power Supply  
5 A 

Power Supply 

USB Type-C 

USB Type-C connector, 5V-20V, 
100W 

Power Supply or USB 
Type-C peripherals 

Debug Serial via USB 

Debug Serial UART console 
over USB for development 

SILICON LABS CP2105 USB to 
UART for both A53 and M4 
processors 

Development Serial 
Connector for debug 
output via USB 

JTAG 

OS / Firmware Programming / 
Debugging JTAG 

10-pin connector 

eMMC / Platform 
programming 
ARM / OpenOCD 
debugging 

Buttons 

General Purpose SW button 

SMD Button 

Additional button for 
general purpose 

Power Button 

SMD Button 

Power Button for 
Suspend / Resume and 
Power off 

Reset Button 

SMD Button 

Button for Reset 

Micro SD (on bottom) 

Micro SD card 

4bit MicroSD SD3.0 card or MMC 
card support 

External Storage 

3.5mm Audio Jack 

Audio Jack supported using 
CIRRUS LOGIC WM8524 
audio codec 

CTIA standard 3.5mm 4-pole audio 
jack providing 24bit 192kHz stereo 
line level audio 

High quality stereo 
audio support 

Audio Expansion 

FPC connector for SAI lines 

Supports SAI1, SAI3, SAI5, SPDIF 
as well as I2C3 and NAND 

FPC connector for audio 
expansion boards 

3 x 0.05mm pitch headers for 
SAI lines 

Supports SAI1, SAI3, SAI5, SPDIF 
as well as I2C3 and NAND 

0.05mm headers for 
audio and GPIO 
expansion 

RJ45 Gigabit Ethernet Connector 

RJ45 jack with 2 bi-color 
LEDs  

RJ45 with internal magnetics, 
supported using AR8031 Gigabit 
Ethernet PHY 

For connecting to a 
wired LAN 

HDMI Type-A Connector 

Extended Display ports 

HDMI port supports up to 4K 
without HDCP 2.0A spec 

External Display 

USB Type-C OTG 

USB Type-C 3.0 OTG 

Type-C connector 

USB client / host port 
for Type-C peripherals 
or main power input 

USB 3.0 

USB 3.0 

Type-A header 

Host port for USB 3.0 
peripherals 

WLAN Antenna 

2X PCB Antenna 

2.4 – 5.1 GHz 

Antenna to SOM WiFi 
module 

LED 

4xLED 

Red : 12V provided and SW400 is on 
Green : CPU is running in overdrive 
mode 
Blue : General purpose 
Orange : General purpose 

 

LCD Display and Touch connector 

100 pin for LCD signals from 
b2b boards for display 

4-lane MIPI DSI, I2C/GPIO, 
Backlight 
MIPI Alliance Specification v1.01  
MIPI D-PHY Specification 
v0.65,v0.81, v0.90, v1.01 

 

M.2 (NGFF) PCI Express –  
Key-E Connector (on bottom) 

M.2 PCI Express Key-E 
connectors for external 
peripheral connectivity 

PCIe1 v2.1 
Can support 2230, 2242, 2260 and 
2280 M.2 sized cards 

For M.2 PCIe add-in 
cards 

Summary of Contents for Open-X 8M







































Reviews: