166
PO
(166PO) AP641 ELECTRIC PUMP ENGLISH 4.875” X 7.25” 05/06/2021
READ AND SAVE THESE INSTRUCTIONS
Page 2
Charging the pump using a standard automobile 12 Volt DC power source:
1. The pump must be charged for 1 hour with 12 Volt DC power source.
2. Plug the 12 Volt DC power cord into the air pump power receptacle
(FIG. 5)
.
3. Attach the DC power cord plug into a standard 12 Volt DC automobile cigarette
lighter or 12V DC accessory outlet
(FIG. 5)
.
4. Slide the switch to
“
” position to charge/recharge the batteries
(FIG. 3)
.
5. Charge: Charge the pump for 1 hour with 12 Volt DC power source.
6. When the pump is charged, immediately remove the power cord.
NOTE:
Red LED light: charging/recharging mode. Green LED light: fully charged.
If the LED light does not light up, make sure the switch is in the “
” position.
INFLATION
When inflating large items such as inflatable boats and large air mattresses, no
accessory nozzle
(FIG. 6)
may be needed. The air pumps inflation connector may
fit directly into the inflation valve. If a nozzle is needed, use the air pump nozzle
most appropriately sized for the product, then follow the instructions below:
Inflation using the 12 Volt DC power cord:
1. Plug the 12 Volt DC power cord into the air pump power receptacle
(FIG. 5)
.
2. Attach the DC power cord plug into a standard 12 Volt DC automobile cigarette
lighter or accessory outlet
(FIG. 5)
.
3. Attach the air pump inflation connector with nozzle if appropriate to the inflation valve on the item to be inflated
(FIG. 7)
.
4. Slide the switch to
“
” position to operate the air pump
(FIG. 8)
. Inflate item to desired level.
5. When the item is inflated, slide the switch to “
” position to turn off the air pump
(FIG. 3)
. Immediately unplug air
pump and cords when air pump is not in use.
Inflation using the air pump when fully charged (without power cord):
1. Attach the air pump inflation connector with nozzle if appropriate to the inflation valve on the
item to be inflated.
2. Slide the switch to
“
” position to operate the air pump
(FIG. 9)
. Inflate item to desired
level.
3. When the item is inflated, slide the switch to “
” position to turn off the air pump.
DEFLATION
Deflation using the DC power cord:
1. Follow steps 1 & 2 under DC power inflation instructions.
2. Attach the air pump deflation connector with nozzle if appropriate
to the deflation valve on the item to be deflated
(FIG. 10)
.
3. Slide the switch to
“
” position to operate the air pump.
Deflate item to desired level.
4. When the item is deflated, slide the switch to “
” position to turn
off the air pump
(FIG. 3)
. Immediately unplug air pump and remove
the cord when air pump is not in use.
Deflation using the air pump when fully charged (without power cord):
1. Attach the air pump deflation connector with nozzle if appropriate into the deflation valve on the item to be deflated.
2. Slide the switch to
“
”
position to operate the air pump. Deflate item to desired level.
3. When the item is deflated, slide the switch to “
” position to turn off the air pump.
FIG (9)
FIG (5)
FIG (10)
FIG (6)
FIG (8)
FIG (7)
OR
©2021 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Recreation Corp. All rights reserved/Tous droits réservés/Todos
los derechos reservados/Alle Rechte vorbehalten. Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous licence de/Marcas
registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen Ländern der Welt in Lizenz von/
Intex Marketing Ltd. to/à/a/an Intex Development Co. Ltd., Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach,
CA 90801
•
Distributed in the European Union by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea por/Vertrieb in
der Europäischen Union durch/
Intex Trading B.V., Venneveld 9, 4705 RR Roosendaal – The Netherlands
www.intexcorp.com
