Interpet Limited warrants this product against defects in
materials or workmanship for a period of 12 months from
the date of original purchase. The warranty covers only any
defects caused during normal use and operation of the
LED, in accordance with the enclosed instructions.
If the product exhibits such a defect, Interpet limited will
repair or replace it without cost for parts or labour. The
product must be shipped pre-paid to Interpet Limited. Proof
of purchase is required. This warranty does not apply to
problems or damage caused by unauthorised modifications,
misuse, improper or inadequate maintenance, accidents, or
operations outside the product instructions or specifications.
All implied warranties, including any implied warranty
of merchantability or fitness for any purpose, are limited
to 12 months from date of original purchase.
The warranty service includes repair or replacement of the LED at
the discretion of Interpet Limited. To the extent allowed by applicable
law, in no event shall Interpet Limited or the manufacturer be liable
for any direct, indirect,special, incidental or consequential damages,
including loss of livestock, arising from a defect in this product.
Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation
may not apply to you if you purchased the product in one of
those states. This warranty provides specific legal rights. You
may have other legal rights that vary from state to state.
Questions or need spare parts, please visit www.interpetlife.com.
Consumer Advice contact details
)
844-660-FISH (3474)
Interpet Ltd. Vincent Lane, Dorking, Surrey, RH4 3YX, UK
www.interpetlife.com
Switch the Life Light off and remove from the brackets – wipe off any
dirt or salt mineral deposits with a damp cloth. Do not use cleaning
agents that could enter the aquarium and harm your livestock.
1.
Do not attempt to dismantle the product other than the
instruction above as this voids your warranty. The information
below should be followed to keep the product in good condition.
2.
Read the manual carefully before operating the
product. Make sure you use the product correctly.
3.
Only use the adaptor supplied with the product.
4.
Do not pull or twist the power cord, or move the product by
holding the power cord only, as this will damage the power cord.
5.
Make sure the power is disconnected before installing or cleaning.
Questions or need spare parts, please visit www.interpetlife.com.
CAUTION:
1.
Before installation of this product, be sure to read and
understand all safety instructions and warnings.
2.
Always unplug this product before any inspection
or disassembling for any reason.
3.
DO NOT SUBMERSE THE PLUG OR CABLE SOCKET.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
70164.
Four options available for fitting the Life Light
a. Hood location with adhesive pads
– Attach the double
sided adhesive pads to the flat surface of the LED. Fix
the Life Light to the underside of the hood in the desired
location – ensure the hood surface is flat, clean and dry. DO
NOT attach directly to fluorescent lamps or lamp reflectors.
b.
Hood location with screws
- Ensure the hood material is
thicker than the length of the screws to prevent them from protruding
through the outer surface. Place the Life Light in the desired
location under the hood. Using the self-tapping screws provided,
fix the LED in position using the fixing holes in the LED.
c. Hood location with glue
– Select desired location on the underside
of the aquarium hood and mark the position of the LED. Keep the
hood away from the aquarium while gluing the LED as the glue can
be dangerous to the fish. Clean the marked area with a damp cloth
then allow to dry, glue into the marked position on the aquarium hood.
An all-round plastic / wood glue is recommended for application.
For example, a 502 super adhesive glue. Always follow the glue
manufacturer’s instructions.
d.
Submersed in Aquarium with suckers
– Attach suckers provided
to the brackets by sliding the button on the sucker into the slot
MAINTENANCE
SAVE THESE INSTRUCTIONS FOR FUTURE USE
WARR ANT Y
INSTALL ATION
SAFET Y INSTRUCTIONS
Installation options
Option a)
Deep & short aquariums for more intensive light.
Option b)
Narrow & long aquariums for even spread of light.
RECOMMENDED USE
(Aquariums up to 20 Gallons)
(Aquariums up to 20 Gallons)
Life Light attachment bracket
Sucker
button slot
in the bracket. Fit the bracket onto the Life Light and place into
desired location in the aquarium (ensure that the LED push fit cable
socket is not submersed) press suckers onto glass (to optimise
adhesion clean the glass before applying the sucker).
