International Harvester Company Cub Cadet 682, Operator'S Manual

Page: 39 / 46

lllllllflATlllll
GIIIIIE
‐
After
Every 10
Hours
of Operation
Check the oil
(with
the
engine
stopped) and add
sufficient new oil to
bring
it to the “FULL” mark on
1 - Engine
oil level gauge.
the
level
gauge. Do
not overfill. Do not
operate the
(check
before each
use)
engine if the
oil level
is
below the “LOW”
mark
on
the gauge.
purpose
lithium
grease
and
apply
sufficient
grease
to flush
out old
grease
and dirt.
Use IH
251H
EP grease or equivalent No. 2
multi ‑
2 - Steering knuckles
(2).
{
NOTE: After the first 10 hours only, remove the
oil
. . . . filter
and
replace
with
a
new
filter. Refer to
“ENGINE
3 ‘ Transm'ss'q" °" “”3“-
AND FUEL
s v s r a r " .
Change the
oil filter after
50
hours and every
100
hours of
operation
thereafter.
‐ After Every 30
Hours
of Operation
Use IH
251H
EP grease or equivalent No. 2 multi ‑
purpose lithium grease and apply
sufficient grease
4 -
Front
Axle
pivot pin.
to flush out old grease and dirt. NOTE: It may be
necessary to
rotate
the
front axle
to
reach
the
grease fitting.
While the oil
is
warm,
remove
the drain
plug
(5) and
drain all of the oil from the crankcase.
Replace
the
drain
plug.
Refill the crankcase with new oil up to the
“FULL” mark on the oil level
gauge. Refer
to
the
“LUBRICATION TABLE”
for the proper quantity
and
viscosity to
use.
5 -Engine
oil drain
plug.
lubricant up to level
plug
6 on the rear of the
transmission case.
6 - Transmission oil level
Check the oil with the
engine stopped. Keep
the
and filler plug.
NOTE: When the r e d hand of
t h e hour
meter is in the red areas maintenance is
required.
36
llIIIIIGATIIIII GIIIIIE
‐
After
Every 10
Hours
of Operation
Check the oil
(with
the
engine
stopped) and add
sufficient new oil to
bring
it to the “FULL” mark on
1 - Engine
oil level
gauge.
the
level gauge. Do not overfiil. Do not
operate the
(check
before each
use)
engine if the
oil level
is
below the “LOW”
mark
on
the gauge.
2 -
Steering
knuckles (2). purpose
lithium
grease and
apply
sufficient grease
{Use
IH 251H EP grease or equivalent No. 2 multi ‑
to
flush out
old grease
and dirt.
NOTE: After the first 10 hours
only,
remove the
oil
filter and replace with a
new
filter. Refer to
“ENGINE
3 ' Transmiss‘Q" °"
“ ” 9 " AND FUEL SYSTEM”.
Change
the oil filter after
50
hours and every 100 hours of
operation
thereafter.
‐ After Every 30
Hours
of Operation
Use
lH
251H
EP
grease or equivalent No.
2
multi ‑
purpose lithium
grease
and
apply
sufficient grease
4 -
Front
Axle
pivot
pin. to flush out old grease and dirt. NOTE: It may be
necessary to
rotate
the front axle
to
reach the
grease fitting.
While the oil
is
warm,
remove
the drain
plug
(5) and
drain all of the oil from the crankcase.
Replace
the
drain
plug.
Refill the crankcase with new oil up to the
“FULL” mark on the oil level
gauge. Refer
to
the
“LUBRICATION TABLE” for the
proper quantity
and
viscosity to
use.
5 - Engine
oil drain
plug.
lubricant up to level
plug
6 on the rear of the
transmission case.
6 - Transmission oil level
Check
the
oil
with
the
engine stopped. Keep the
and filler plug.
NOTE: When the red hand of
t h e hour
meter is in the red areas maintenance is
required.
36
< , _ _ ; I A , . . “ 9 ‐ . “
_ . , A
...
s
7 ' :
‐ . . a "
_ , _