Intermec PM43 Service Manual Download Page 50 | Manualshive

Page: 50 / 70

Intermec PM43 Service Manual Download Page 50

TITLE

Model

DOCUMENT NO.

PAGE

PM43 Service Work Instructions

PM43,PM43C

SWIPM43x-000

Page

50 of 70

Intermec Proprietary Document

OPERATION:

Main Logic Board (MLB) Assembly

Remove all installed interface option (RFID, Wi-Fi/Bluetooth, USB interface, parallel interface, DUART interface, etc.) board
prior to removing the MLB. See Figure 3 as a reference with all the options and connections.

Tools Required

Description

Part Number

Torx Driver

T20

Nut Driver

5mm or 3/16

Parts Required

Item Part Number

Description

Qty

1

234-032S-001

PCB ASSY,MLB, Spare (include 5 Torx screws PN 1-994059-008. Does not
include grounding plate and hex standoffs)

1

2

318-051-001

Real Time Clock (RTC) Battery, Accessory

1

3

1-994059-008

Screw, MRT 4x8 ZP, T20, (14 lbf.in/16 kgf.cm)

5

Main Logic Board (MLB) Replacement

1. Remove 5 Torx screws that secure the MLB. For printer with installed option, there will be 4 Torx screws and a
standoff. See Figure 1 for reference.
2. Remove standoff for printer with installed options

Figure 1 – Main Logic Board

Spare MLB

3. Disconnect all attached cablings and carefully remove MLB away from the power supply back plate. See Figure 3.
4. Remove the grounding plate and hex standoffs  from the defective MLB and install onto replacement MLB.  See Figure 2.
  (

Note: This procedure is necessary for initial built of spare MLB that did not include grounding plate and standoff

)

Figure 2

MLB Grounding Plate & Hex Standoff

3

3

3

3

1

Optional Real-Time Clock
(RTC) Battery

1

3

Standoff with
installed option

2

1

«
...
48
49
50
51
52
...
»

Summary of Contents for PM43







































































Reviews:

No comments