ADJUSTING DIP SWITCH SETTINGS
The occupancy sensor features 2 DIP switch settings. Each setting can be set to an up or down position to
configure the DIP switch setting. Follow these steps to adjust the DIP switch settings.
1. Adjust the sensitivity level DIP Switch (1). The Up position sets the sensitivity to 50%, while the down position
adjusts the sensitivity level to 100%.
DIP SWITCH 1 - SENSITIVITY LEVEL SETTINGS
50%
UP position
100%
Down positions
2. 2. Adjust the Vacancy feature DIP Switch (2).
NOTE: Turn this DIP switch to ON if you have a momentary switch. This enables overrides.
DIP SWITCH 2 - VACANCY LEVEL SETTINGS
Enable
UP position
Disable
Down positions
3. Install the front on the sensor and secure with the screws.
TESTING THE OCCUPANCY SENSORS
1. Ensure the PIR Activity is enabled, the Red LED flashes, and the PIR Sensitivity is set to MAX (DIP switch 1 OFF).
2. Ensure the Time Delay is set for TEST MODE.
3. Ensure the Light Level is the default (maximum).
4. Remain stationary until the lights turn OFF. The Red LED and Load are ON.
5. Once the lights turn off, move around the coverage area. The lights will illuminate.
6. When testing and adjustment is complete, reset DIP Switches and Light Level to the desired settings and replace the cover on the sensor.
TROUBLESHOOTING
The PIR activity LED does not flash properly,
The warm-up period has not been completed
Make sure the circuit breaker is on
Set the PIR sensitivity to Max/Autoset (DIP switch 1 OFF)
Check all sensor connections
There is improper PIR activity, LED flashes
Make sure the light level adjustment is set properly by covering the PIR lens and PIR activity LED to verify if
lights turn on. If lights still turn on, adjust the light level.
The sensor is activating without detecting
The PIR sensitivity is set too high. Adjust the PIR sensitivity.
movement.
The sensor is mounted too close to HVAC or VAV vents with heavy air flow. Relocate the sensor.
Set the DIP switch 1 to ON
158--01285
1 2
ON
1 2
Sensitivit
y
Up Position
Down Position
DIP SWITCH
DIP Switch
Settings
Settings Chart
Va
canc
y
LIMITED TWO YEAR WARRANTY
If within the warranty period specified, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of charge. This warranty is extended to the original
purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or any negligent use; (b) units which have been subject to
unauthorized repair, opened, taken apart or otherwise modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost of the product; (e) sealed lamps and/or lamp bulbs, LED’s and
batteries; (f) the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED
WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS
LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED
WARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) completing a warranty claim on line at www.intermatic.com. This warranty is made by:
Intermatic Incorporated, Customer Service 7777 Winn Rd. Spring Grove, Illinois 60081-9698. For warranty service go to: http://www.intermatic.com or call 815-675-7000.
