FM1D Series
One Circuit Electronic
24 Hour or 7 Day Time Switches
FM1D20A
(surface mounting)
FM1D20E
(flush mounting)
APPLICATION
Time based control of lighting, ventilating, heating, cooling or other
electrical loads in commercial and industrial applications. The
FM1D Series time switches are programmable for 24-hour or
7-day schedules.
The FM1D20A and FM1D50A Series Time Switches are intended
for either surface or Din Rail mounting. The control is completely
enclosed in a plastic housing and includes a terminal cover and
sub-base for installation and hard wiring.
The FM1D20E Series and FM1D50E Series Time Switches are
intended for flush (panel) mounting.
Both models are supplied with a clear plastic dust cover.
TECHNICAL DATA
Output–1 SPDT relay with dry contacts
Switch Rating:
N.O. Contact:
-1/2hp, 120 V ac
-1hp, 240 V ac
-8 A, 24 V dc resistive
-16 A, 277 V ac resistive
-12 A Ballast, 120 V ac
-8 A Ballast, 240 V ac
-720 VA 240 V ac Pilot Duty
-360 VA 120 V ac Pilot Duty
-1000W Tungsten,240 V ac
-600W Tungsten,120 V ac
3 year Reserve (Non-Replaceable Battery)
Supply voltages: Separate Models –
FM1D20Series:
FM1D50 Series:
24VAC/DC,
12 VAC/DC,
120VAC,
24 VAC/DC,
240VAC,
120 VAC,
240 VAC.
All Models 60Hz (refer to product label)
Shortest switch time–1 minute
Ambient Temperature Range –14°F to 131°F (–10°C to 55°C)
VA required: 120V & 240V models: 4VA
24V model: 2VA @ 24VAC, 1VA @ 24VDC
Screw terminal connections (FM1D20A and FM1D50A)
1/4” quick connects (FM1D20E and FM1D50E)
Accuracy ± 4 minutes per year
Agency Approvals: UL Recognized
INSTALLATION
To the installer:
1. Read operating instructions carefully.
2. Check the input and output ratings marked on the unit to
make sure this product is suitable for your power supply and
application.
3. Disconnect power supply prior to installation to prevent
electrical shock.
4. Wire in accordance with National and Local electrical code
requirements.
SURFACE MOUNTING—FM1D20A and FM1D50A
Remove dust cover, loosen two screws on opposite corners.
Remove the housing that surrounds the time switch and the
terminal cover away from the base. Remove timer module by
pulling straight out.
Place screws through 3 mounting holes in base and screw to
back panel or wall.
Wire in accordance with instructions. Replace terminal cover
and push timer firmly onto base. Now replace housing and
secure with screws.
PANEL MOUNTING—FM1D20E and FM1D50E
Cut a square hole 2-5/8” x 2-5/8” (66mm x 66mm) in the front
of the panel. Insert the time switch through the opening. With
a screwdriver, press down and turn outer screws (A) until
flanges are in position to fasten the unit in front panel, then
release. Insert plugs into holes (B).
Use 1/4” quick connects and make connections in accor-
dance with the wiring diagram shown and applicable code
requirements.
WIRING
1. Disconnect the power.
2. Wire input to timer,
2
4
5
3
1
M
COM
120V
LINE
NEUTRAL
NO
NC
LOAD
M
, with the
proper voltage marked on the unit.
Wiring to incorrect voltage will void
the warranty.
3. Connect wiring according to the
wiring diagram. The terminals on
the Digi 20A sub-base will
accommodate 10 to 24 AWG wire.
Terminal Connections
B
A
A
B
N.C. Contact
-16 A, 277 V ac resistive
-8 A, 24 V dc Pilot Duty
-360 VA, 120 V ac Pilot Duty
