Setting Sunset ON / Fixed Time OFF
1. If necessary, press the
MODE
button repeatedly until the words
SET, ASTRO, and ON/OFF EVENTS appear in the upper area of
the display.
2. Press the
ENTER
button if necessary to display ON @.
3. Make sure you know which days you want the Sunset ON event
to be active.
- If you want the Event to turn ON every day of the week, press
the
DAY
button to display SUNSET and all days.
- If you want the Event to turn ON for a different combination of
days, press the
DAY
button again as necessary to cycle through
the days or combination of days you want.
To remove an individual day, press the
DAY
button until the
day is blinking, then press the
–
button.
4. Press the
MODE
button as necessary to display SET, FIXED and
ON/OFF EVENT.
5. Press the
ENTER
button as necessary to display OFF @ and
EVENT 02.
6. Press the
DAY
button to display 12:00 am and all days of the
week.
7. Press the
+
or
–
buttons to enter the time you want to set.
To go from AM to PM, keep pressing the
+
or
–
buttons to cycle
through the day. You can hold the
+
or
–
buttons down for 3
seconds to make the time scroll quickly.
8. If you want the Event to occur for a combination of days rather
than every day (e.g., weekends only, weekdays only, or individual
days), press the
DAY
button again as necessary to cycle through
the individual days or combination of days you want.
NOTE:
To choose a combination not shown during cycling
(e.g., Tuesday and Thursday), you must create an individual
event for each of the days you want.
6. ET8215C ONLY
—For a multi-circuit device with loads set
independently, you can choose the load you want the event to
control. The default setting is for both loads, as you can see on
the display. Press the
ON/OFF
button under a load to remove the
load from the event.
7. When you have set the event correctly, you have two choices:
- Press the
ENTER
button to set the next fixed time event (up to
28 events).
- Press the
MODE
button to exit.
Press the
MODE
button repeatedly to select the desired operating
mode on the display. There are 2 options:
• AUTO
—where the Time Switch follows the events you have
programmed, turning the circuits ON and OFF at the time(s) set.
NOTE:
You can override programmed events and force the
Time Switch ON or OFF by pressing
the
ON/OFF
button.
• MANUAL
—where any events set are disabled and the Time Switch
controls all circuits through the
ON/OFF
button.
NOTE:
You can review or edit any programmed events at any time by
pressing the
MODE
button repeatedly to return to the appropriate menu,
then following programming instruction provided on this sheet.
Operating the Time Switch
Use this procedure to clear the settings programmed for an event.
1. If necessary, press the
MODE
button repeatedly until the words
SET, FIXED, and ON/OFF EVENTS are shown on the display.
2. Press the
ENTER
button as necessary to cycle through events that
have been set until you see the event you want to delete.
3. Press the
+
or
–
buttons AT THE SAME TIME to display --:-- --.
4. Press the
MODE
button to exit.
OPTIONAL – Deleting (Clearing) an Event
158--01578
• Batteries can be easily replaced without removing the Time Switch
mechanism or field wiring.
• Press in and downward (in the direction of the arrows) on the
battery cover.
• It is recommended to replace the batteries every 2-3 years with 2
AAA industrial grade alkaline cells as part of normal maintenance
on the Time Switch.
• Be sure to observe battery polarity markings when installing
batteries.
• No other battery maintenance is required.
Battery Maintenance
9.
ET8215 ONLY—
For a multi-circuit device with loads set
independently, you can choose the load you want the event to
control. The default setting is for both loads, as you can see on
the display. Press the
ON/OFF
button under a load to remove the
load from the event.
10. When you have set the event correctly, you have two choices:
- Press the
ENTER
button to set the next fixed time event (up to
28 events).
- Press the
MODE
button to exit.
INTERMATIC INCORPORATED, SPRING GROVE, ILLINOIS 60081-9698
LIMITED ONE-YEAR WARRANTY
If within the warranty period specified, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of charge.
This warranty is extended to the original household purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse
in handling, acts of God or any negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart or otherwise modified; (c) units not used in accordance
with instructions; (d) damages exceeding the cost of the product; (e) sealed lamps and/or lamp bulbs, LED’s and batteries; (f) the finish on any portion of the product, such as surface
and/or weathering, as this is considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR
IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE
HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME
STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased or (b) completing a warranty claim online at www.intermatic.com. This warranty is
made by: Intermatic Incorporated, Customer Service 7777 Winn Rd., Spring Grove, Illinois 60081-9698. For warranty service go to: http://www.Intermatic.com or call 815-675-7000.
Experience in the field has shown that is the most commonly used
setting for the Time Switch. These instructions cover the entire
procedure.
