Interlogix MC251-4P/1S User Manual Download Page 2

ii                                                              IFS MC251-4P/1S and NS2051-4P/1T User Manual 

Copyright

 

© 2013  UTC Fire & Security Americas Corporation, Inc.  

Interlogix is part of UTC Climate Controls & Security, a unit of 
United Technologies Corporation.  All rights reserved. 

Trademarks and

patents

 

The IFS MC251-4P/1S and NS2051-4P/1T and logo are 
trademarks of United Technologies. 
Other trade names used in this document may be trademarks or 
registered trademarks of the manufacturers or vendors of the 
respective products. 

Intended use

 

Use this product only for the purpose it was designed for; refer to 
the data sheet and user documentation for details. For the latest 
product information, contact your local supplier or visit us online 
at www.interlogix.com. 

Manufacturer

 

UTC Fire & Security Americas Corporation, Inc.  
2955 Red Hill Avenue 
Costa Mesa, CA 92626-5923, USA  
EU authorized manufacturing representative: 
UTC Fire & Security B.V., Kelvinstraat 7,  
6003 DH Weert, The Netherlands 

Certification

 

 

 N4131 

FCC compliance

 

This equipment has been tested and found to comply with the 
limits for a Class A digital device, pursuant to part 15 of the FCC 
Rules. These limits are designed to provide reasonable 
protection against harmful interference when the equipment is 
operated in a commercial environment. This equipment 
generates, uses, and can radiate radio frequency energy and, if 
not installed and used in accordance with the instruction manual, 
may cause harmful interference to radio communications. 
You are cautioned that any changes or modifications not 
expressly approved by the party responsible for compliance 
could void the user's authority to operate the equipment. 

ACMA compliance 

Notice!

 This is a Class A product. In a domestic environment 

this product may cause radio interference in which case the user 
may be required to take adequate measures. 

Canada 

This Class A digital apparatus complies with Canadian ICES-
003.Cet appareil numérique de la classe A est conforme á la 
norme NMB-003du Canada. 

European Union 

directives

 2004/108/EC 

(EMC 

Directive): 

Hereby, UTC Fire & Security 

Americas Corporation, Inc. declares that this device is in 
compliance with the essential requirements and other relevant 
provisions of Directive 2004/108/EC.

 

 

 

 2002/96/EC 

(WEEE 

directive): 

Products marked with this 

symbol cannot be disposed of as unsorted municipal waste in 
the European Union. For proper recycling, return this product to 
your local supplier upon the purchase of equivalent new 
equipment, or dispose of it at designated collection points. For 
more information see: www.recyclethis.info.

 

Contact information

 

For contact information see our Web site: www.interlogix.com. 

Contact support

 www.interlogix.com/customer 

support 

 

 
 

Summary of Contents for MC251-4P/1S




























Reviews: