manualshive.com logo in svg

Interlogix IFS MC352-4P-2S, User Manual, Page: 17 / 31

Share
Download
Interlogix IFS MC352-4P-2S User Manual Download Page 17

  

- 17 - 

 

IFS Model 

SFP Description 

S30-1SLC/A-10 

SFP, LC Connector, Single Mode, Gigabit,    1 fiber, 1310nm/1550nm, 10km , A 
End 

S30-1SLC/A-20 

SFP, LC Connector, Single Mode, Gigabit,    1 fiber, 1310nm/1550nm, 20km, A 
End 

S30-1SLC/A-60 

SFP, LC Connector, Single Mode, Gigabit,    1 fiber, 1310nm/1550nm, 60km, A 
End 

S30-1SLC/B-10 

SFP, LC Connector, Single Mode, Gigabit,    1 fiber, 1550nm/1310nm, 10km , B 
End 

S30-1SLC/B-20 

SFP, LC Connector, Single Mode, Gigabit,    1 fiber, 1550nm/1310nm, 20km, B 
End 

S30-1SLC/B-60 

SFP, LC Connector, Single Mode, Gigabit,    1 fiber, 1550nm/1310nm, 60km, B 
End 

S30-2MLC 

SFP, LC Connector, Multi Mode, Gigabit,    2 fiber,850nm/850nm, 550m 

S30-2MLC-2 

SFP, LC Connector, Multi Mode, Gigabit,    2 fiber,1310nm/1310nm, 2km 

S30-2SLC-10 

SFP, LC Connector, Single Mode, Gigabit,    2 fiber,1310nm/1310nm, 10km 

S30-2SLC-30 

SFP, LC Connector, Single Mode, Gigabit,    2 fiber,1310nm/1310nm, 30km 

S30-2SLC-70 

SFP, LC Connector, Single Mode, Gigabit,    2 fiber,1550nm/1550nm, 70km 

S30-RJ 

SFP, RJ-45, Gigabit, 100m 

1000Base-SX/LX: 

Before connecting with switches, workstation or media converter, please do the following steps: 

1. 

With 1000Base-X Fiber Speed, please set the DIP Switch of SFP Port 5 or Port 6 to the “OFF” 

position. 

 
 
 
 
 
2. 

Make sure both sides of the SFP transceivers are with the same media type, for example: 
1000Base-SX to 1000Base-SX, 1000Base-LX to 1000Base-LX. 

3. 

Check whether the fiber-optic cable type matches with the SFP transceiver model. 

  To connect to 1000Base-SX SFP transceiver, use the Multi-mode fiber cable with one side 

being the male duplex LC connector type. 

  To connect to 1000Base-LX SFP transceiver, use the Single-mode fiber cable with one side 

being the male duplex LC connector type. 

 

 

Connecting the fiber cable 

1. 

Insert the duplex LC connector on the network cable into the SFP transceiver. 

2. 

Connect the other end of the cable to a device – switches with SFP installed, fiber NIC on a 
workstation or a media converter. 

3. 

Check the LNK/ACT LED of the SFP slot on the front of the Industrial Gigabit PoE+ Switch. Ensure 
that the SFP transceiver is operating correctly. 

 

OFF 

ON 

Port 6 (DIP 2) 

1000X 

100FX 

Port 5 (DIP 1) 

1000X 

100FX 

Summary of Contents for IFS MC352-4P-2S
































Reviews:

No comments