ES3002
-4P-
4T User Manual
Package contents
Thank you for purchasing
the E
S30
02-4P-4T
IFS
8-Port
10/100/1000T
Gigabit Ethernet Switch
with 4
-Port 802.3at
PoE+ Injector.
Unless specified
, the term “
gigabit Ethernet switch
”
mentioned in this user manual refers to
the E
S30
02-4P-4T.
Open the box of the gigabit Ethernet switch
and carefully
unpack it. The box should contain the following items:
•
G
igabit ethernet switch × 1
•
CD with user manual × 1
•
Power cord
× 1
•
Rubber feet × 4
•
19” rack-
mounting brackets with attachment screws × 1
If any of these
pieces are missing or damaged, please contact
your dealer immediately. If possible, retain the carton including
the original packing material, and use them again to repa
ck the
product in case there is a need to return it to us for repair.
Introduction
Product description
To fulfill the demand of sufficient PoE power for network
applications with Gigabit speed transmission, the ES3002
-4P-
4T 8-Port 10/100/1000T Gigabit Ethe
rnet Switch with 4
-Port
802.3at PoE+ Injector, a member of the 802.3at PoE Gigabit
Ethernet Switch family, features high
-
performance Gigabit
IEEE 802.3at PoE (up to 30 W) and a full 60 W PoE budget on
half of the switch’s eight 10/100/1000Mbps TP ports. The four
802.3at PoE+ ports provide a PoE power injector function that
can drive two IEEE 802.3at or 4 IEEE 802.3af compliant
powered devices. The ES3002
-4P-4T also provides simple,
cost-
effective, and non
-
blocking wire
-
speed performance with
an 8.5-inch met
al housing suitable for desktop deployment for
SOHO and department network applications.
All RJ45 copper interfaces in the ES3002
-4P-
4T support
10/100/1000Mbps auto
-
negotiation for optimal speed detection
through RJ45 Category 6, 5, or 5e cables. It also supports
standard auto
-
MDI/MDI
-
X that can detect the type of
connection to any Ethernet device without requiring special
straight-
through or crossover cables
.
Features
Physical Port
•
8-
port 10/100/1000BASE
-
T Gigabit Ethernet RJ45 copper
•
4-
port IEEE 802.3at/af PoE Injector (Port
-1 to Port-
4)
Power over Ethernet
•
Complies with IEEE 802.3af/at Power over Ethernet end
-
span PSE
•
Up to four ports of IEEE 802.3af/802.3at devices powered
•
Supports PoE power up to 30.8 W for each PoE port
•
Each port supports 53 VDC power to PoE powered device
•
60 W PoE budget
•
Auto detects powered device (PD)
•
Circuit protection prevents power interference between
ports
•
Remote power feeding up to 100 m with standard mode,
200 m with extended mode
Switching
•
Hardware based
10/100/1000Mbps auto
-negotiation and
auto MDI/MDI
-X
•
Flow control for full duplex operation and back pressure
for half duplex operation
•
IEEE 802.1Q VLAN transparency
•
Hardware DIP switch for “Standard” and “Extend” mode
selection; the “Extend” mode features 30 W PoE transmit
distance of 200 m at speed of 10 Mbps (only for Port1
–
Port4)
Hardware
•
8.5-
inch desktop size, 1U height, rack mountable
•
LED indicators for system power, per port PoE ready and
PoE activity, speed, Link/Act
•
Fan
-
free design
•
Supports Energy
-
Efficient Ethernet (EEE) function (IEEE
802.3az)
Specifications
Hardware specifications
Hardware version
2
10/100/1000BASE
-T
MDI/MDIX
ports
8
PoE Injector Port
Four
ports with 802.3at/af PoE
injector function with Port
-1 to Port-
4
Switch Architecture
Store
-and-
Forward
Switch Fabric
16
Gbps/non-blocking
Switch Throughput@64 bytes
11.9
Mpps@64
b
ytes
MAC Address Table
4K entries,
automatic source
address learning and aging
© 2017 United Technologies Corporation.
P/N 1073337-EN
• REV
A
• ISS
19JUL17
Interlogix is part of UTC Climate, Controls & Security, a unit of United Technologies Corporation.
All rights reserved.
