Interactive Intelligence Interaction Edge Installation And Configuration Manual Download

Page: 44 / 62

Interaction Edge IPMI reference

Sensor Readings

Select this tab to display the current state of the hardware in the Interaction Edge appliance.

This page contains the following controls:

Item

Description

Select a sensor type category

list box

This control enables you to select which sensors
are displayed in the table.

Table

This control displays the current observed state
from the sensor, the name of the sensor, the
status of the observed component, and the
current reading for the component.

Refresh

button

This control refreshes the sensor data that is
displayed in the table. The data is not
automatically refreshed.

Show Thresholds

button

This control displays the minimum and
maximum states that a sensor observed for the
associated component in the table on this page.

Event Log

Select this tab to display the events that have occurred regarding the IPMI or Interaction Edge hardware
components.

This page contains the following controls:

Item

Description

Select an event log category

list box

This control enables you to select which events
are displayed in the table.

Table

This control displays the event items for the
currently selected category.

Clear Event Log

button

This control removes all events from the log.

Caution!

This action cannot be undone.

Configuration

This area enables you to change settings for the IPMI and for the Interaction Edge appliance. It contains the
following tabs:













Summary of Contents for Interaction Edge































































Search results

Summary of Contents for Interaction Edge

Reviews:

Related manuals for Interaction Edge

Brands by name

Popular brands

Interactive Intelligence Interaction Edge, Installation And Configuration Manual

Search results

Summary of Contents for Interaction Edge

Reviews:

Related manuals for Interaction Edge

Brands by name

Popular brands