a. LEVEL Adjustment
b. ALC Adjustment
Mounting a Camera
Mounting a Camera
(1) Mounting a Lens
(2) Connection
(3) Lens Adjustment
Back focus adjust
(4) Setting Switch
Lens Adjustment
Lens Adjustment
1. Video Adjustment
Connect the camera according to the connection method, turn it on, display a image on the
monitor, and check the image. The camera has been factory-adjusted best position, but it may need
to be adjusted according to the object conditions of lens.
Connection
Connection
1. When the camera is powered, the POWER LED lights up.
2. Connect to the video monitor, etc. (75
Ω
)
3. This camera is originally designed to be mounted from the bottom, as shown.
Mounting a Lens
Mounting a Lens
1. Before mounting a lens, check whether it is a C-mount or CS-mount lens.
* The F mark indicates a focal point.
2. Mount the lens on the camera by turning the lens clockwise.
Adjust its position.
3. When using an auto-iris lens with an EE amplifier, turn the switch to the “VIDEO” side.
When no EE amplifier is equipped, turn the switch to the “DC” side.
* Video Iris Lens [3-pin terminal]
* DC Iris Lens [4-pin plug]
4. If the cable is too long, house it in the camera mounting bracket.
LENS
Flange back (B)
Dimension (A)
C-mount Lens
17.526mm
10mm or less
CS-mount Lens
12.5mm
5.5mm or less
A
B
F
*F: Focal point
Pin No
Lens
Video Iris Lens
1
9.5V [max 50mA]
2
GND
3
VIDEO
Pin No
Lens
DC Iris Lens
1
Brake
2
Brake
3
Drive
4
Drive
Monitor Screen
LEVEL Turning Direction
Too bright
Counterclockwise (Toward L)
Too dark
Clockwise (Toward H)
Monitor Screen
ALC Turning Direction
Part (high-intensity part) of the screen halates.
Clockwise (Toward PK)
Other part of screen (except high-intensity part) darkens.
Counterclockwise (Toward H)
Back Focus Adjustment
Back Focus Adjustment
The back focus has been factory-adjusted to the best point for CS-mount lens, but it may need to be re-
adjusted if the mount is changed to the C-mount or when a different lens is used.
If required, adjust it as follows.
- With a fixed-focus lens
If the focus can not be adjusted correctly by rotating the lens focus ring, adjust the back focus as
follows.
1. Loosen the back focus locking screw by turning it counterclockwise with a screwdriver.
2. Turn the back focus adjustment ring to focus at the best point.
3. Tighten the back focus locking screw by turning its clockwise.
- With a zoom lens
If the image is out of focus when zooming (with-angle telephoto), adjust the camera as follows.
1. Shoot a comparatively dark scene with thin lines about three meters away from the came.
2. Set the lens to the maximum telephoto position, and adjust the lens focus.
3. Set the lens to the maximum wide-angle position, and adjust the focus.
4. Repeat step 2 and 3 two or three times.
Setting Switch
Setting Switch
1. [RESET] RESET button.
2. [R] White Balance red control, [–] Line Lock vertical
phase control.
3. [B] White Balance blue control, [+] Line Lock vertical
phase control.
4. [WHT BAL] White balance control mode, [PHASE]
Line lock phase control mode.
5. [INT] Internal mode, [LL] To set the LL mode.
6. [MANU] [AUTO] White balance select control
mode.
7. [BLC ON/OFF] Back Light Compensation Switch
8. [AES ON/OFF] Automatic Electronic Shutter
9. [AGC ON/OFF] Auto Gain Control Switch
10. [DC LEVEL] DC Iris Lens Level Control
11. [FOR SERVICE] Interface connector. This connector is used for service.
1
2
3 4 5 6
7 8 9
11
10
DIGITAL COLOR CAMERA
DIGITAL COLOR CAMERA
