Intellitec ST410, Instruction

Page: 9 / 28

ITEM
VALUE
1 2 3 4 5 6 7 8 9
1. Low-voltage protection 2.6V/Cell 2.8V/Cell 3.0V/Cell 3.2V/Cell 3.4V/Cell Not activated
2. Running mode Forward with
brake and no
reverse
Forward with
brake / paus
and reverse
Forward with
reverse. No
brake!
3. Motor timing Very low Low Normal High Very high
4. Initial acceleration Low Medium High Very high
5. Throttle percent reverse 20% 30% 40% 50% 60% 70% 80% 90% 100%
6. Throttle limit 0% 20% 30% 40% 50% 60% 70% 80% 90%
7. Percent brake 10% 20% 30% 40% 50% 60% 70% 80% 90%
8. Dragbrake 0% 4% 8% 12% 15% 20% 25% 30%
9. Motor rotation Normal Reverse
10. Neutral rangel 2% 3% 4% 5% 6% 10%
ZTW ESC can be adjusted with a program card (option) to your driving style. Factory defaults are marked in gray boxes.
1. Low-voltage protection:
Set the voltage of cells when ESC will cut off the power to protect the batteries (LiPo).
When using NiMH this does not need to be activated.
Note:
As factory default the protection is turned off.
It must be activated with a program card (option) before using LiPo batteries.
2. Running mode:
1. Forward without reverse. 2. Forward with pause, then reverse - ESC needs throttle to be in neutral
for 2 seconds before reverse can be activated. This is to protect the transmission in the model.
3. Forward with reverse - in this mode the model can go forward and reverse, but has no brake.
3. Motor timing:
Adjust the motor performance and driving time. Low timing = lower performance = longer driving
time. High timing = high performance = less driving time. Value 5 should be used with caution!!
4. Initial acceleration: Adjust the initial power to motor when starting from a complete stop.
Low value gives slow acceleration and longer driving time. High value gives high acceleration and less driving time.
A very high acceleration can be very tough on the batteries as the amperage draw can be very high. If your vehicle cuts
out, hesitates or loses radio control, you should consider setting this at a lower value. Use with caution!
5. Throttle percent reverse:
A lower value gives slower speed when going in reverse.
6. Throttle limit:
A lower value gives slower speed when going forward.
7. Percent brake:
The effect on the brakes
8. Drag brake:
The drag brake function provides the driver a set percentage of brake when you have the
transmitter in neutral.
9. Motor rotation:
Normal or reverse.
10. Neutral range:
This setting adjusts the amount of “Dead band” off neutral on the throttle trigger.
The smaller the value the less “Dead band” or movement is required off-center for the ESC to begin throttle functions.
Using a higher value for this setting will provide a wider Dead band.
Programming options
The ZTW Program card with LED display is easy to use and convenient to carry. All of the programmable functions are
shown on the program card.
1. Turn on the ESC. Remove the Signal wire and plug it into the top-socket on the Program card, wait for 2 seconds until
the LED is ON. The first programmable function will be shown, if an error occurs, please re-connect.
2. If ESC is not connected with the batteries, the Program card should be connected with another power supply,
the range of power supply is within 5.0-6.3V.
3. Press the button “Menu” on the Program card and select each programmable function. At that time the number of
the programmable function will be displayed on the left of the LED, the current value will be displayed on the right side.
Then press the button Value to change the value and press the button OK to confirm. At the same time the Red indi-
cating LEDs of both program card and the ESC blink. Turn off the ESC, the modified settings will be saved in the ESC’s
memory.
4. Press the button Reset to restore the default settings.
Using the ZTW program card
EN
Gray boxes indicates factory settings.