Intelligent Weighing Technology Intell-Lab IL-0.0001 g, Service Manual

Page: 20 / 47

PROCEDURE TO LINEARIZE EMC BALANCES IL-0.0001, PB-
0.001, PB-0.01g RELEASE R2.xx
For model with four point of linearity
1 .
2 .
3 .
4 .
5 .
6 .
Switch on balance.
After 30 min press ON/OFF button.
Press sequentially buttons ON/OFF - CAL
– CAL.
You will see "Lin" on display, press ENTER to confirm..
The display
shows on the left number “1” wait stability and after 3 seconds press CAL to confirm.
When the balance and show number 2 on the left put first weight, (table weight for linearity) wait
stability and after 3 seconds press CAL to confirm.
Put second weight, wait stability and after 3 seconds press CAL to confirm.
Put third weight, wait stability and after 3 seconds press CAL to confirm.
After this point, press CAL and keep it pressed until the display show number 3 on the left.
Then press ON/OFF to return to weighing mode.
Calibrated the balance and check linearity.
Attention: if you forget point 9 the data will not be stored and you will have to do again the
linearization procedure.
For model with seven point of linearity
Switch on balance.
After 30 min press ON/OFF button.
Press sequentially buttons ON/OFF - CAL
– CAL.
You will see "Lin" on display, press ENTER to confirm..
The display
shows on the left number “1” wait stability and after 3 seconds press CAL to confirm.
When the balance and show number 2 on the left put first weight, (table weight for linearity) wait
stability and after 3 seconds press CAL to confirm.
Put second weight, wait stability and after 3 seconds press CAL to
confirm. Put third weight, wait stability and after 3 seconds press CAL
to confirm. Put fourth weight, wait stability and after 3 seconds press
CAL to confirm. Put fifth weight, wait stability and after 3 seconds
press CAL to confirm. Put sixth weight, wait stability and after 3
seconds press CAL to confirm.
After this point, press CAL and keep it pressed until the display show number 3 on the
left. Then press ON/OFF to return to weighing mode.
Calibrated the balance and check linearity.
Attention: if you forget point 9 the data will not be stored and you will have to do again the
linearization procedure.
For model with twelve point of linearity
Switch on balance.
After 30 min press ON/OFF button.
Press sequentially buttons ON/OFF - CAL
– CAL.
You will see "Lin" on display, press ENTER to confirm..
The display show on the left number “1” wait stability and after 3 seconds press CAL to confirm.
When the balance and show number 2 on the left put first weight, (table weight for linearity) wait
stability and after 3 seconds press CAL to confirm.
Put second weight, wait stability and after 3 seconds press CAL to
confirm. Put third weight, wait stability and after 3 seconds press CAL
to confirm. Put fourth weight, wait stability and after 3 seconds press
CAL to confirm. Put fifth weight, wait stability and after 3 seconds press
CAL to confirm. Put sixth weight, wait stability and after 3 seconds
press CAL to confirm. Put seventh weight, wait stability and after 3
seconds press CAL to confirm. Put eighth weight, wait stability and after
3 seconds press CAL to confirm. Put ninth weight, wait stability and
after 3 seconds press CAL to confirm. Put tenth weight, wait stability
and after 3 seconds press CAL to confirm. Put eleventh weight, wait
stability and after 3 seconds press CAL to confirm. Put twelfth weight,
wait stability and after 3 seconds press CAL to confirm.
The balance goes automatically in stand-by status ; press ON/OFF to return to weighing mode.
Calibrated the balance and check linearity.
1 .
2 .
3 .
4 .
5 .
6 .
7 .
8 .
9 .
10 .
11 .
12 .
13 .
14 .
15 .
1 .
2 .
3 .
4 .
5 .
6 .
7 .
8 .
9 .
10 .
11 .
12 .
13 .
14 .
15 .
16 .
17 .
18 .
19 .