background image

Pag.4   

 www.intelligenthanddryers.com

Dryflow® Vapordri Hand Dryer

2. INTRODUCTION

The main features of the Dryflow® Vapordri hand dryer are the following:

•  Automatic functioning.

 The hand dryer will automatically turn on when hands are detected by IR 

sensors. Sensibility of these sensors can be regulated through the potentiometers placed inside 

the device.

•  HEPA filter .

 The device is equipped with large HEPA filter which requires less frequent replacement 

and facilitates aspiration, which increases air flow. The filter is easy to access, clean and remove.

•  Antibacterial ABS.

 The device is manufactured from ABS plastic which contains some additives 

that avoid proliferation of bacteria, fungi and mould. 

•  Water tank.

 Hand dryer has a wáter tank to recover wáter from hands during drying process. The 

wáter tank must be empty and cleaned regularly.

•  High performance and low consumption.

 Heating element of the device turns off automatically 

when room temperature is above 25º, saving energy.

•  High performance.

 Drying time is only between 10 to 12 seconds, what makes it suitable for areas 

with high traffic of people.

•  Alarms.

 Several alarms are included to warn about maintenance needs: water tank full, change of 

HEPA filters, change of motor brushes.

Summary of Contents for Dryflow Vapordri

















Reviews: