Intel Vectra VEi7 Installation Manual Download Page 17 | Manualshive

Page: 17 / 34

Intel Vectra VEi7 Installation Manual Download Page 17

7 Installing the Intel EtherExpress Pro 100B-TX PCI Ethernet Adapter

Microsoft Windows NT 4.0 Workstation

7 Installing the Intel EtherExpress Pro 100B-TX PCI
Ethernet Adapter

Microsoft Windows NT
4.0 Workstation

Connecting to a Novell
NetWare 3.12 Server

Requirements

•

HP Vectra with Windows NT 4.0 Workstation.

•

Intel EtherExpress PRO 100B-TX PCI Ethernet adapter and driver disk
version 2.51.

•

Driver File: E100BNT.SYS, version 2.24

•

Microsoft Windows NT 4.0 Workstation media.

•

Microsoft Windows NT 4.0 Service Pack 4 media.

•

Novell NetWare 3.12 Server system that supports IPX network protocol.

•

Novell IntranetWare Client for Windows NT v4.11b installation media.

Device Configuration

Procedure

1

With the HP Vectra turned off, install the Intel EtherExpress PRO 100B
PCI adapter card into a PCI slot.

2

Connect network cable media to the Intel EtherExpress PRO 100B card.

3

Power on the machine and start in MS-DOS mode.

4

Insert the Intel driver disk, “EtherExpress PRO/100B LAN Adapter
Configuration and Drivers Diskette” and execute “SETUP.EXE”.

5

Select “CONFIGURE NIC” and verify the resource settings listed above
under the heading “Device Configuration”.

6

If changes are required, save those changes and exit.

7

Remove the Intel Software driver diskette and restart the system.

Device Configuration

Vectra Vli8

Vectra VEi7

Vectra VEi8

Interrupt

05

03

10

I/O Address

1020

DCE0

E400

«
...
15
16
17
18
19
...
»

Summary of Contents for Vectra VEi7



































Reviews:

No comments